Quantcast
Jump to content

Newbie w/ T2 looking for some parts

pulvin54

By pulvin54
in New Members Area

 Share

Recommended Posts

pulvin54 Rookie

pulvin54

Posted
Posted

Hey all,

Not new to forums but new to this one. Just picked up a Joyner T2 and looking to make a couple of upgrades. I finally was able to locate a half decent wiring diagram but if anyone has one I'd sure appreciate another one ( the one I downloaded is ok but zooming in blurs the font). I'd like to put a hard top on it. I'm not aware of anyone that makes one. I was just gonna attempt to cut out part of an old truck bed liner. I also need to replace the boots on it and I read somewhere that the boots for a '96 GEO Metro will work? Also, I have no idea what year it is. I've looked all over it and the only thing I've found is the sticker on the firewall behind the driver's seat. It states that this machine meets the 2008 CA emissions standards. Even the VIN plate doesn't have the year stamped on it. Any help would be great. Thanks.

Link to comment
Share on other sites
  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • CYJSP2009
      2022 brandnew Joyner CV Axles and CV Joint rebuild kits are comming
      By CYJSP2009
      Dear Friends, 
      2022 Brand new Joyner CV Axles and CV  Joint rebuild kits are comming 
      1.  S650.03.02.02.00 ---Joyner 650 Commando Rear
      2. TR1100.03.01.03.00 --- Joyner Trooper Front 
      3. TR1100.03.02.03.00 --- Joyner Trooper Rear
      4. D650.03.02.02.00 --- Joyner 650 Sand Spider Rear Left 
      5. D650.03.02.03.00--- Joyner 650 Sand Spider Rear Right 
      6. SV800.03.02.01.00 --- Joyner 800 Viper, SV1100 Drive shaft Left
      7.  14274 --- 650 ider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      8. 15803  ---  650 Sand Spider rear left, rear right, 800 MV; 800Viper, SV1100 Drive shaft rear left and rear right outer cv joint rebuild kit
      Attached are the part photos for reference. 
      Above parts are now on the way to USA, will be ready for inland delivery in middle of July. 
      Price: CV Axle: USD250/ Piece;  CV Joint kit （without grease): USD110  send to door. 
      There will be special discount availabe for deals completed within July 2022.  
      Buy 1 piece: Get 5% discount, 
      Buy 2 pieces: get 10% discount.
      Buy 3 pieces: get 15% discount, 
      Buy 4 and more than 4 pieces: get 20% discount. 
      Please kindly note Qty for each part is not big  and it is hard to forcast when there will be next offer for these kind of products unless there is sufficient confirmed order qty for productioin arrangement. 
      Payment method: Payoneer payment link ( can pay through bank account or credit card) or Paypal ( [email protected]) .  Payment commission paid by the buyer. 
      Interested parties, please contact [email protected]. 
      Thanks
      Good Luck
      Casey / Leaf Asia
      July-07-2022
       
       
       














    • MJG
      Looking to Purchase 2008 Joyner Renegade
      By MJG
      Hello, 
      I found an 08 Renegade for sale and looking to purchase it.  I haven’t heard too much about these machines and any insight would be much appreciated.  Are they good machines?
    • Steve Toney
      New member
      By Steve Toney
      Hello, my name is Steve and just signing up.  Bought my first UTV yesterday.  It is a Massimo T-Boss 550.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...