Quantcast
Jump to content

New Product Showcase

Sign in to follow this  

NEW Utility Vehicle Products Discussions! Do you know of a product or accessory that others should know about? Post it in this forum,

25 topics in this forum

    • 12 replies
    • 6,783 views
  1. UTV High Seat

    • 0 replies
    • 4,874 views
    • 7 replies
    • 4,775 views
  2. New UTV Light Bar

    • 3 replies
    • 4,046 views
    • 0 replies
    • 3,861 views
    • 3 replies
    • 3,358 views
  3. DWT new sector wheel

    • 0 replies
    • 3,085 views
    • 0 replies
    • 3,037 views
  4. NEW UTV

    • 1 reply
    • 2,925 views
    • 0 replies
    • 2,839 views
  5. ATV PONY CART

    • 1 reply
    • 2,730 views
    • 0 replies
    • 2,704 views
  6. The Spot

    • 3 replies
    • 2,533 views
  7. UTV Loading Ramp

    • 0 replies
    • 2,530 views
    • 0 replies
    • 2,474 views
    • 0 replies
    • 2,470 views
    • 0 replies
    • 2,371 views
    • 2 replies
    • 2,285 views
  8. RZR Cooler Trunk

    • 1 reply
    • 2,163 views
  9. RZR Mask

    • 0 replies
    • 2,082 views
    • 0 replies
    • 1,699 views
    • 0 replies
    • 1,563 views
  10. Zip open Windows

    • 0 replies
    • 1,287 views
    • 4 replies
    • 985 views
    • 0 replies
    • 413 views
Sign in to follow this  


  • Latest Posts

    • She's a runner!  Waiting on some special tools to get here as I have some tuning to do on the clutch. Clutch stalls the motor a bit high, so I have a feeling it's all caked with mud in the clutch sliders.  Runs good though!   
    • Stuck float should be easy. locate the carb, take off the bowl, (bowl nut on carb, ) the float should be level, not hanging down.   fuel pump: Pretty much, just replace it. They don't make any repair parts for them.   Found this thread reply on another forum, seems to be a common problem with the 610  a dirty carburetor...or a bad float ...or a bad inlet needle.   What is happening is that the gasoline is bypassing the float needle and is overflowing. Then it goes through this passageways and into the oil pan.   IF there is dirt that has gotten onto the needle or seat, this will hold the needle open.   If there is a small hole in the float, then the float will sink allowing too much gas to enter the carburetor. causing this problem.   If the needle or seat has worn or has a chip in it, then the gas will bypass them and flow into the oil.   This is a very common problem.   ALSO, if you have a vacuum operated fuel pump, the diaphram inside the pump may have gotten a hole in it. This will allow gasoline to pass through the diaphram and into the oil supply.  
    • Don't know if this will help, but it looked interesting, and possibly relevant. If you end up finding that the fuel pump is the problem. I'm not sure what obstacle the poster ran into that made him go this way, instead of an actual repair. But sometimes there's little choice. But until we know what the problem is, this is a cheap alternative, and a quick fix. If it's a stuck float, a fuel cut off is always a good idea anyway. And it'll stop that particular issue. Although it won't actually fix the real problem, it'll stop the unwanted gas.
    • Travis, any advice on how to check for these conditions? I'm not much of a mechanic but a fast learner.
    • Contact me, I have the service manual I can give you 562-682-7859 Matt


×