Quantcast
Jump to content

UTV Ride Reports - Where to Ride

Sign in to follow this  

Report your UTV rides here. Please post as much information, location, pictures, etc..as you can. Post Riding area inquiries. Find out where to ride that UTV!

53 topics in this forum

    • 0 replies
    • 1,949 views
    • 0 replies
    • 1,541 views
    • 0 replies
    • 1,552 views
    • 2 replies
    • 4,038 views
  1. I'm off to Borneo

    • 2 replies
    • 2,658 views
    • 0 replies
    • 2,275 views
    • 2 replies
    • 1,971 views
    • 0 replies
    • 1,734 views
    • 0 replies
    • 1,985 views
    • 2 replies
    • 2,457 views
    • 4 replies
    • 2,893 views
    • 0 replies
    • 2,250 views
  2. Paiute Trail Utah

    • 6 replies
    • 5,729 views
    • 0 replies
    • 1,734 views
    • 1 reply
    • 2,063 views
  3. Black Mountain

    • 0 replies
    • 1,433 views
    • 0 replies
    • 1,386 views
    • 3 replies
    • 1,998 views
    • 1 reply
    • 1,533 views
  4. Oregon UTV areas

    • 2 replies
    • 3,450 views
    • 1 reply
    • 2,083 views
    • 0 replies
    • 1,261 views
    • 17 replies
    • 3,179 views
  5. Places to ride in Mo

    • 0 replies
    • 1,821 views
  6. New Places to ride

    • 2 replies
    • 3,233 views
Sign in to follow this  


  • Latest Posts

    • Wow, thanks for all the great references. I will let you know what I find in a couple weeks.
      Cheers  
    • She's a runner!  Waiting on some special tools to get here as I have some tuning to do on the clutch. Clutch stalls the motor a bit high, so I have a feeling it's all caked with mud in the clutch sliders.  Runs good though!   
    • Stuck float should be easy. locate the carb, take off the bowl, (bowl nut on carb, ) the float should be level, not hanging down.   fuel pump: Pretty much, just replace it. They don't make any repair parts for them.   Found this thread reply on another forum, seems to be a common problem with the 610  a dirty carburetor...or a bad float ...or a bad inlet needle.   What is happening is that the gasoline is bypassing the float needle and is overflowing. Then it goes through this passageways and into the oil pan.   IF there is dirt that has gotten onto the needle or seat, this will hold the needle open.   If there is a small hole in the float, then the float will sink allowing too much gas to enter the carburetor. causing this problem.   If the needle or seat has worn or has a chip in it, then the gas will bypass them and flow into the oil.   This is a very common problem.   ALSO, if you have a vacuum operated fuel pump, the diaphram inside the pump may have gotten a hole in it. This will allow gasoline to pass through the diaphram and into the oil supply.  
    • Don't know if this will help, but it looked interesting, and possibly relevant. If you end up finding that the fuel pump is the problem. I'm not sure what obstacle the poster ran into that made him go this way, instead of an actual repair. But sometimes there's little choice. But until we know what the problem is, this is a cheap alternative, and a quick fix. If it's a stuck float, a fuel cut off is always a good idea anyway. And it'll stop that particular issue. Although it won't actually fix the real problem, it'll stop the unwanted gas.
    • Travis, any advice on how to check for these conditions? I'm not much of a mechanic but a fast learner.


×