Quantcast
Jump to content

UTV General Discussion

UTV Side by Side General Discussions Forum. Please post UTV related topics in this forum only.

238 topics in this forum

  1. TRYING TO DECIDE BETWEEN?????

    • 61 replies
    • 12,839 views
    • 31 replies
    • 18,470 views
  2. Quieter exhaust!

    • 20 replies
    • 1,708 views
  3. What Oil to use?

    • 16 replies
    • 502 views
    • 15 replies
    • 3,361 views
  4. Splutter

    • 14 replies
    • 1,339 views
    • 12 replies
    • 3,890 views
  5. Insurance???

    • 12 replies
    • 4,541 views
    • 11 replies
    • 4,173 views
  6. Fuel tank leak

    • 11 replies
    • 472 views
  7. Looking for a UTV

    • 11 replies
    • 872 views
  8. Arizona

    • 10 replies
    • 2,809 views
    • 10 replies
    • 9,146 views
  9. Newbie help

    • 10 replies
    • 1,029 views
    • 10 replies
    • 1,007 views
    • 9 replies
    • 5,880 views
    • 9 replies
    • 364 views
    • 8 replies
    • 12,818 views
  10. Somewhere WARM!

    • 8 replies
    • 2,221 views
    • 7 replies
    • 3,087 views
  11. Local Utah site?

    • 7 replies
    • 1,362 views
  12. Landmaster opinions

    • 7 replies
    • 3,251 views
  13. dump bed problems

    • 7 replies
    • 519 views
    • 7 replies
    • 288 views
  14. CVT pulley removal help

    • 7 replies
    • 49 views


  • Latest Posts

    • Ooh! Them heads are beat up! I noticed in the 4th picture, the head on the right,by the exhaust valve on the bottom next to the seat looks like a vertical crack... Is it? the cylinder looks good from what I can tell, except a few score lines, if possible take it to a machine shop and have them mic both, and hone them, shouldn't cost more than $50., And measure the crank journals, although they look excellent, it's cheap insurance from all your work blowing up.   https://www.amazon.com/Lucas-Oil-10152-Assembly-Lube/dp/B000WJ3M6I/ref=asc_df_B000WJ3M6I/?tag=bingshoppinga-20&linkCode=df0&hvadid={creative}&hvpos={adposition}&hvnetw=o&hvrand={random}&hvpone=&hvptwo=&hvqmt=e&hvdev=t&hvdvcmdl={devicemodel}&hvlocint=&hvlocphy=&hvtargid=pla-4583932699391023&psc=1 Lucas oil assembly lube, good stuff, coat all the cam and crank the,crankpin and valve springs. look forward to seeing your work!!
    • Hey Strike, Its a carbed unit.  I well try to get pictures of it
    • The Yardsport YS400 is a mix of parts from the Yamaha parts bin. The manufacture is HiSUN, who also happens to manufacture parts for Yamaha and more OEM's. The bottom end is basicaly the same as the Yamaha 350 Grizzly/Bruin. The top end is more of less off of a Yamaha Kodiak 400, early 2002 style. I would start by using OEM Yamaha parts for the clutch. 2007-2011 Yamaha Grizzly 350 wet clutch. the parts are of higher quality than the Chinese counterparts. This might be part of your problem. They bolt right on and will work and last much better.
    • Here is the wiring diagram for the single wire type. Along with a pic of the sensor in the cylinder head. The color of the single wire might be White with Blue tracer.
    • Update:   it came off fine,  just a few taps with the rubber mallet.  Once that was out of my way, I was able to assess the carnage, pretty bad, was not a rod issue as described after all, looks like the screws that hold the air filter housing on rattled into the engine and banged up both chambers, and pistons.  Both intake valves had closed on 2 of the screws, other chunks of piston.   Not all bad as the case is fine, save for some light scoring that should clean up in one cylinder.   The crank, and both rods seem fine, I need to check the intake valves again,  both seem like they may be usable, not sure yet.   The heads took the brunt of the damage and will cost the most.  Pricey parts.  Will see if I can get them tig welded and repair the chamber surface as they are pretty bad.  
        Some more pics


×