Quantcast
Jump to content

General Discussion - Anything

You can post threads on anything general in here. This forum does not have to contain anything related to UTVs!

149 topics in this forum

  1. QLINK FrontRunner

    • 16 replies
    • 28,619 views
    • 15 replies
    • 18,154 views
  2. What about joke section

    • 62 replies
    • 9,141 views
  3. Happy Thanksgiving!

    • 28 replies
    • 5,572 views
    • 22 replies
    • 4,823 views
  4. Where's everybody?

    • 27 replies
    • 4,731 views
  5. Trailer ramp assist

    • 5 replies
    • 4,365 views
  6. Freezing!

    • 17 replies
    • 3,623 views
    • 1 reply
    • 3,579 views
    • 1 reply
    • 2,822 views
  7. Funny crap

    • 7 replies
    • 2,749 views
  8. HEAD LIGHTS

    • 1 reply
    • 2,601 views
  9. Freakin' HOT !

    • 10 replies
    • 2,599 views
  10. Where NEXT !

    • 9 replies
    • 2,567 views
  11. TIRES

    • 9 replies
    • 2,486 views
  12. DuckDuckGo.com

    • 4 replies
    • 2,478 views
    • 6 replies
    • 2,373 views
  13. Messages

    • 6 replies
    • 2,212 views
  14. MegZ is a MOMMY!!!!

    • 8 replies
    • 2,160 views
  15. Shocks

    • 8 replies
    • 2,138 views
  16. FUSE & RELAY BOX

    • 2 replies
    • 2,120 views
  17. Weather

    • 11 replies
    • 2,085 views
    • 6 replies
    • 2,073 views
  18. Merry Christmas

    • 6 replies
    • 2,040 views
  19. Favorite band(s)?

    • 4 replies
    • 2,028 views


  • Latest Posts

    • Stuck float should be easy. locate the carb, take off the bowl, (bowl nut on carb, ) the float should be level, not hanging down.   fuel pump: Pretty much, just replace it. They don't make any repair parts for them.   Found this thread reply on another forum, seems to be a common problem with the 610  a dirty carburetor...or a bad float ...or a bad inlet needle.   What is happening is that the gasoline is bypassing the float needle and is overflowing. Then it goes through this passageways and into the oil pan.   IF there is dirt that has gotten onto the needle or seat, this will hold the needle open.   If there is a small hole in the float, then the float will sink allowing too much gas to enter the carburetor. causing this problem.   If the needle or seat has worn or has a chip in it, then the gas will bypass them and flow into the oil.   This is a very common problem.   ALSO, if you have a vacuum operated fuel pump, the diaphram inside the pump may have gotten a hole in it. This will allow gasoline to pass through the diaphram and into the oil supply.  
    • Don't know if this will help, but it looked interesting, and possibly relevant. If you end up finding that the fuel pump is the problem. I'm not sure what obstacle the poster ran into that made him go this way, instead of an actual repair. But sometimes there's little choice. But until we know what the problem is, this is a cheap alternative, and a quick fix. If it's a stuck float, a fuel cut off is always a good idea anyway. And it'll stop that particular issue. Although it won't actually fix the real problem, it'll stop the unwanted gas.
    • Travis, any advice on how to check for these conditions? I'm not much of a mechanic but a fast learner.
    • Contact me, I have the service manual I can give you 562-682-7859 Matt
    • Is the seatbelt plugged in? It has a limiter if not connected 


×