Quantcast
Jump to content

General Discussion - Anything

You can post threads on anything general in here. This forum does not have to contain anything related to UTVs!

149 topics in this forum

  1. Season Greetings

    • 1 reply
    • 874 views
  2. Utv/ATV X-mas Accessories

    • 3 replies
    • 1,245 views
  3. GPS

    • 6 replies
    • 1,863 views
  4. TIRES

    • 9 replies
    • 2,487 views
    • 5 replies
    • 1,488 views
  5. GO OBAMA!

    • 6 replies
    • 1,415 views
  6. Anyone use the SHOUTBOX?

    • 3 replies
    • 1,044 views
  7. Funny crap

    • 7 replies
    • 2,749 views
    • 2 replies
    • 926 views
  8. Hey all you guests

    • 2 replies
    • 1,245 views
  9. Shocks

    • 8 replies
    • 2,139 views
  10. Happy Birthday Blaze379!

    • 1 reply
    • 934 views
  11. Pictures anyone???

    • 2 replies
    • 1,704 views
    • 0 replies
    • 994 views
    • 0 replies
    • 1,232 views
  12. rrrrr ads by Google

    • 2 replies
    • 1,704 views
    • 1 reply
    • 1,749 views
    • 0 replies
    • 1,254 views
    • 0 replies
    • 1,103 views
  13. Looking to Buy a UTV

    • 2 replies
    • 1,419 views
  14. What are your FALL plans?

    • 2 replies
    • 1,384 views
  15. About Posting

    • 1 reply
    • 1,740 views
    • 4 replies
    • 1,723 views
    • 5 replies
    • 1,780 views


  • Latest Posts

    • Wow, thanks for all the great references. I will let you know what I find in a couple weeks.
      Cheers  
    • She's a runner!  Waiting on some special tools to get here as I have some tuning to do on the clutch. Clutch stalls the motor a bit high, so I have a feeling it's all caked with mud in the clutch sliders.  Runs good though!   
    • Stuck float should be easy. locate the carb, take off the bowl, (bowl nut on carb, ) the float should be level, not hanging down.   fuel pump: Pretty much, just replace it. They don't make any repair parts for them.   Found this thread reply on another forum, seems to be a common problem with the 610  a dirty carburetor...or a bad float ...or a bad inlet needle.   What is happening is that the gasoline is bypassing the float needle and is overflowing. Then it goes through this passageways and into the oil pan.   IF there is dirt that has gotten onto the needle or seat, this will hold the needle open.   If there is a small hole in the float, then the float will sink allowing too much gas to enter the carburetor. causing this problem.   If the needle or seat has worn or has a chip in it, then the gas will bypass them and flow into the oil.   This is a very common problem.   ALSO, if you have a vacuum operated fuel pump, the diaphram inside the pump may have gotten a hole in it. This will allow gasoline to pass through the diaphram and into the oil supply.  
    • Don't know if this will help, but it looked interesting, and possibly relevant. If you end up finding that the fuel pump is the problem. I'm not sure what obstacle the poster ran into that made him go this way, instead of an actual repair. But sometimes there's little choice. But until we know what the problem is, this is a cheap alternative, and a quick fix. If it's a stuck float, a fuel cut off is always a good idea anyway. And it'll stop that particular issue. Although it won't actually fix the real problem, it'll stop the unwanted gas.
    • Travis, any advice on how to check for these conditions? I'm not much of a mechanic but a fast learner.


×