Quantcast
Jump to content

New Members Area

Are you a new member to UTVBoard.com? Stop by here and introduce yourself. Tell us about yourself, your vehicle, etc.

167 topics in this forum

    • 3 replies
    • 95 views
  1. New UTV owner

    • 3 replies
    • 111 views
  2. Throttle

    • 1 reply
    • 133 views
  3. Newbie

    • 4 replies
    • 171 views
    • 2 replies
    • 304 views
  4. new member

    • 5 replies
    • 157 views
    • 2 replies
    • 148 views
  5. New to board and UTV/ATV

    • 4 replies
    • 192 views
  6. Hey Guys!

    • 2 replies
    • 161 views
  7. 2011 yardsport

    • 5 replies
    • 269 views
    • 2 replies
    • 433 views
    • 2 replies
    • 510 views
    • 2 replies
    • 350 views
  8. To hot to ride

    • 1 reply
    • 301 views
  9. Af450 mule engine

    • 0 replies
    • 463 views
    • 0 replies
    • 419 views
  10. First Time UTV Buyer

    • 4 replies
    • 523 views
  11. Hisun Utv 500 help

    • 7 replies
    • 813 views
  12. Newbie

    • 2 replies
    • 304 views
  13. New guy

    • 1 reply
    • 281 views
  14. Hello

    • 1 reply
    • 296 views
  15. Newbie

    • 2 replies
    • 306 views
    • 1 reply
    • 371 views
  16. New guy

    • 1 reply
    • 284 views
  17. Hello, New member

    • 3 replies
    • 410 views


  • Latest Posts

    • Stuck float should be easy. locate the carb, take off the bowl, (bowl nut on carb, ) the float should be level, not hanging down.   fuel pump: Pretty much, just replace it. They don't make any repair parts for them.   Found this thread reply on another forum, seems to be a common problem with the 610  a dirty carburetor...or a bad float ...or a bad inlet needle.   What is happening is that the gasoline is bypassing the float needle and is overflowing. Then it goes through this passageways and into the oil pan.   IF there is dirt that has gotten onto the needle or seat, this will hold the needle open.   If there is a small hole in the float, then the float will sink allowing too much gas to enter the carburetor. causing this problem.   If the needle or seat has worn or has a chip in it, then the gas will bypass them and flow into the oil.   This is a very common problem.   ALSO, if you have a vacuum operated fuel pump, the diaphram inside the pump may have gotten a hole in it. This will allow gasoline to pass through the diaphram and into the oil supply.  
    • Don't know if this will help, but it looked interesting, and possibly relevant. If you end up finding that the fuel pump is the problem. I'm not sure what obstacle the poster ran into that made him go this way, instead of an actual repair. But sometimes there's little choice. But until we know what the problem is, this is a cheap alternative, and a quick fix. If it's a stuck float, a fuel cut off is always a good idea anyway. And it'll stop that particular issue. Although it won't actually fix the real problem, it'll stop the unwanted gas.
    • Travis, any advice on how to check for these conditions? I'm not much of a mechanic but a fast learner.
    • Contact me, I have the service manual I can give you 562-682-7859 Matt
    • Is the seatbelt plugged in? It has a limiter if not connected 


×