Leaderboard

Since I've seen some questions on this I took some pictures and will provide instructions on a valve adjustment for the UT400. This should be the same for the 550's and other various Coleman/Hisun single cylinder models with the cylinder slanted aft. I have seen several people ask of it is really necessary, and read several reports of valves being out of adjustment from the factory. My valves were .004" intake, and .010" exhaust with about 5 hrs on the machine. I've seen different numbers thrown around for factory spec, but I decided to go with 0.005". This is called valve lash. What is is is a gap between the rocker arm and the valve then the camshaft isnt opening the valve. Why does it matter? If it's too large the valve doesn't open all the way, if it's too small the valve dosent close. This can cause valve damage (overheating) as well as loss of engine power (burned fuel is going out exhaust rather than pushing the piston dow). Tools required : 5MM Allen wrench, 10MM box wrench, needle nose pliers, flat feeler gauge set, rags First you need to remove the fan cover on the passenger side. There is a cooling vent hose on the back side, remove the hose clamp and slide it off. From there there are 4x 10mm bolts holding the cover. The forward ones can be accessed from under the seat. Next remove the spark plug from the drivers side. Carefully wiggle the spark plug wire off. Grip it as low as possible and give it a little twisting motion as you pull it off to help free it. Its a tight fit for a socket, but there is a sheet metal wrench in the toolkit that fits it. Unscrew the plug and set it aside. This allows you to spin the motor over freely with no compression to fight. When you reassemble this is a good opportunity to switch to an NGK iridium plug for better performance/less fouling DR8EIX) Next you need to remove the intake and exhaust valve covers. The intake us the forward one. There are 3x 5MM Allen screws to remove. The Exhaust is the rear with 2x 5MM Allen bolts. Both covers have O-Rings instead of gaskets and are reusable. When you remove the rear be careful and use your rags as there will be oil that drips out. Next up we need to spin the motor over to top dead center. Grab each rocker arm and give em a little wiggle up and down. Spin the engine over by grabbing the fan with your other hand. Spin the engine over until both rockers have some wiggle and are loose. Once both rockers are loose slide the feeler gauge in like shown above. Try different feelers as needed to determine your starting spec. You should feel some drag but still be able to move the feeler without too much force. If you need to adjust, use the 10MM wrench to slightly loosen the locknut, then with the correct feeler gauge in place, tighten the top square nut while wiggling the feeler in and out. Once you have it right you need to tighten the 10mm lock nut without moving the square head bolt. Once the lock nut is tight recheck the clearance. That's it, button everything back up and make sure you have it all reassembled before running it again. If you find this helpful give me a thumbs up or comment. If you have any questions or need more help let me know. If there's interest maybe I'll do some more of these

Hey Folks There are not a lot of good sources out there for troubleshooting and diagnosing ECU problems with the Massimo Buck, Bennche Bighorn, Bennche Cowboy, & Cazador machines that use the Delphi MT05 ECU. They are all basically the same with different badging, so I thought I'd share some info that I found during some searches. I was trying to help someone diagnose and repair a hard starting issue. The ignition coil was throwing a 0351 code. I discovered how to read codes without an OBDII code reader. The following procedures should help you check your fault codes and clear them if needed. Fault Code Troubleshooting for Delphi MT05 ECU on the Massimo Buck 400, Bennche Bighorn 400, Bennche Cowboy 400, and Cazador 400 *NOTE: The MT05 ECU is not really OBD 2 compliant. It is much more similar to an OBDI system. The MT05 ECU controls either 1 or 2 cylinder engines commonly found on Massimo, Bennche, and Cazador. Much of the ECU info was found here: https://netcult.ch/elmue/HUD ECU Hacker/Delphi MT05 Manual.pdf Delphi EFI System Design Delphi EFI employs 5 sensors to monitor engine performance. 1. Crankshaft Position Sensor 2. Coolant Temperature Sensor 3. Oxygen Sensor 4. Throttle Position Sensor 5. Manifold Air Pressure/Manifold Air Temperature (MAP/MAT) Sensor Delphi EFI employs the following system components. 1. MT05 Engine Control Unit (ECU) 2. Fuel Pump 3. Multec 3.5 Fuel Injector 4. Idle Speed Control Valve (Idle Stepper Motor) 5. Multec Ignition Coil 6. Fuel Vapor Canister Purge Valve Using the Digital Dashboard to Decipher EFI Trouble Codes In addition to commercially available diagnostic scan tools (Big $$$), you can use the engine warning light of the Siemens dashboard to diagnose most of your EFI problems. The digital dashboard receives signals from the MT05 ECU, and the engine warning light will flash a diagnostic trouble code (DTC) if the ignition key is switched on/off for three cycles. When you turn on the ignition, the engine warning light will illuminate, which indicates the EFI system is operational. After the engine is started, the engine warning light will extinguish if the EFI system is working properly. However, if the engine warning light remains illuminated, it indicates the EFI system is not working properly, and there is a system component failure. Deciphering Diagnostic Trouble Codes To read the diagnostic trouble code (DTC), open and close the ignition key three times in rapid succession, as follows: open/close—open/close—open. At this point the engine warning light will flash a DTC which indicates the fault in the EFI system. Refer to the attached fault code table to identify the corresponding problem. The engine warning light will emit a sequence of flashing lights. If the light flashes 10 times, the translated number is 0. If the light flashes one time, the translated number is 1, et cetera. For example, if the MAP/MAT sensor is disconnected, or the connector is shorted to ground, the engine warning light will flash in the following manner (This is an example only). The engine warning light will flash 10 times: The first number of the DTC is 0 After an interval of 1.2 seconds, the engine warning light will flash 1 time: The second number of the DTC is 1 After an interval of 1.2 seconds, the engine warning light will flash 10 times: The third number of the DTC is 0 After an interval of 1.2 seconds, the engine warning light will flash 7 times: The fourth number of the DTC is 7 The resulting DTC is P0107. NOTE: For the system I was helping to troubleshoot, I suspected an ignition coil failure due to the code that was thrown. When it was checked, it was flashing: 10, 3, 5, 1. The 10 represents a 0. So the actual code was 0351. After finding the code, the coil wire was checked and discovered loose at the spark plug. Once it was pushed fully on, the problem was fixed. Most likely, this problem was created after the owner had pulled the spark plug to check the gap. The ECU was rebooted using the procedures detailed below with no more codes being thrown. If there are other fault codes, the engine warning light will flash the next code in 3.2 seconds after finishing the first sequence. After all existing fault codes are flashed, the engine warning light will repeat the fault codes in a loop sequence, until the ignition key is turned off. To clear fault codes you either need an OBDII Fault Code reader and a Delphi 6 pin connector adapter cable that you have to order from China and wait 8 weeks…OR....you can simply reboot the ECU using the instructions detailed below. Rebooting the ECU Perform the following steps to reboot the ECU. 1. Turn off the ignition for 15 seconds. 2. Turn the ignition on/off for 5 cycles. Make sure each cycle lasts about ½ second, verifying the start of the fuel pump for each cycle. If the fuel pump doesn't start during any cycle, begin the entire reboot procedure from the beginning. 3. Turn off the ignition for 15 seconds. TPS (throttle position sensor) re-learn procedure after rebooting ECU. This should be done after replacing the TPS or the ECU....and it is advisable to check proper idle after rebooting an ECU too. Source: ECU Hacker (Reworded process slightly to make it a more sensible flow in my mind): 1. Turn the idle screw one full turn clockwise before starting 2. Start the engine, and run at low idle until the engine warms. Maybe a couple of mins. 3. Idle should be above 1500 rpm. If it isn’t, turn it up to 1700 then shut the engine off. Do another reboot of ECU. 4. Restart the engine and let it stabilize at 1700 rpm. Then turn the idle screen down to 1500 rpm and let it stabilize for a few seconds. Once it stabilizes, set to the final recommended idle speed for your machine. The placard under (or behind) your seat should show idle speed, valve adjustment, spark gap, etc. Typically the 390 cc engines in the "400" machines run at 1600 rpm idle. 5. Shut it down. Wait 10-15 seconds before restarting. The procedure is now complete. Final Notes: I have included pictures of an OBDII connector and the Delphi 6 pin connector in case anyone wants to go buy stuff off ebay or local parts suppliers and build a connector to use for an OBDII reader. But...you can save money and simply do the same thing with code reading and resetting using the check engine light on your dash. Some folks prefer to do it with code readers. Hope the information provided helps if anyone ever needs it but cannot find it in repair manuals. I discovered most of this in some motorcycle forums. The source for the diagrams is here: https://netcult.ch/elmue/HUD ECU Hacker/ Be advised: I am not a service technician. I do not endorse any manufacturers. I do not get paid to help, nor do I want to. This is just a hobby of mine. I enjoy working on things and solving problems. If you run into a weird problem that stumps you, give me a shout. I may be able to give you some ideas...or not. Just know, that troubleshooting thru emails can be challenging. The more info you can provide, the better. Otherwise, I will probably ask you a ton of questions. The good news is, the Delphi system used on these machines is essentially an OBDI and it is very simplistic. If you are methodical and patient, most of your "problems" can be figured out thru a process of elimination. Always go for the simple things first before throwing money and sensors at a machine. Take care - JT

In order to connect with the ECU we need two cables. The first is a USB ODBII cable. HUD ECU Hacker’s documentation has a lot of different confusing options, but here’s what I went with and managed to get working, the cable is called “VAG KKL” it is a USB to ODB2 cable. It is available from a variety of sources for $10-15. The second thing we need is a “6 pin delphi to ODB2” adapter cable. It is also available for a similar price. In my case I ordered both from ebay, but there are other sources. Once we have our cable in hand we need to find the plug it in on your machine. My personal rig is a Coleman UT400, but the wire location should be similar for all Hisuns. My cable was located under the middle of the seat area. Just inboard of the battery, where the main wire harness split loom runs. The cable is a 6 pin (3x2) with a dust cap. Remove the dust cap and plug in the 6-pin end of the Delphi adapter cable. Note: When I was done, I left the 6-pin adapter connected, and zip tied it so it now runs to in front of the battery for easier access in the future. Next download and install HUD ECU HACKER DOWNLOAD Open HUD ECU Hacker on your PC It should prompt you to choose a driver to install. This particular cable uses the “CH340” driver (First choice on the menu) click to install, once installed hit the X in the corner to go back to the main page Once the driver is installed plug in the USB Cable, and plug the ODB2 end into the 6 pin adapter. The red led on the adapter should light up indicating it has power. Drop down and pick a com port on the main screen, it should show the VAG KKL adapter as a com port. Click connect on the main menu. It will pop up a bunch of fast scrolling text indicating it is connecting. Once connected you can click through the various tabs to see different data sets. The main menu also has the option to show fault codes, clear fault codes, reset the EPROM back to factory. The other function that may be helpful is recording a log file. You can record a log while operating the unit, and come back later and replay it to try to better diagnose what is happening. Within the various pages you will see the reading from each sensor. Sometimes a sensor reading will be off enough to cause running issues, but not enough for the ECU to realize its an issue. For example if the engine thinks it’s really warm, but its actually cold, it may not inject enough fuel to start. There are also more advanced functions, like adjusting fuel mapping, but that is beyond the scope of this tutorial. Full HUD ECU Hacker Documentation (Very technical reading) If you find this helpful give me a comment below or a thumbs up.

White smoke is usually coolant leaking into the cylinder. Sounds like a blown head gasket to me.

Just wanted to give update . It was the ecm. Put new one on and got spark immediately to front cylinder. Ran but smoking and no power. I checked back cylinder and no fire. Pulled coil to check with meter and found wire was not getting good connection where it plugs into coil. All good now . She will scream !!!. Next is to figure out why 4x4 switch wont turn. Thanks for all the imput....

Hello to anyone who reads this. I am Jon and I own J&M Outdoor Power, a very small, small engine repair shop. I was approached by Coleman about 6 months ago to become one of their Warranty Centers. I recently received 3 different UT400's and a UT500 all with similar issues. These units range from 2 months to 2 years old. Customers state that the unit(s) was/were running fine, then heard a pop and a loss of power, two would no longer start. The two that would run would not achieve normal operating speed (around 20mph I would say) without redlining the RPMs. I quickly found that the Valve lash on each unit had become too large on some(both intake and exhaust) and too tight on one(just intake). After setting the gaps to .005(I found multiple different people suggesting bigger and smaller gaps, but no definitive Coleman Spec number yet) every unit starts, runs, and achieves top speed without issue. I don't know how many others have come across these issues, and I wanted to get something out on the web for others in the same predicament. Please let me know if you have had similar issues. Edit: I realize that this will not be a fix all solution for this issue, as the oil level and condition should be verified before moving to the valves. Many times improper oil conditions will cause valve lash to change. These units all have good oil and proper oil changes.

Hello again! I now have a pretty good running Coleman UT400 after a top end rebuild, wet clutch rebuild and a repaired crankcase... ! It plows snow great, but I was also having the jumping out of gear problem, mainly reverse, but a couple times out of forward. I would quickly place it in N and then let the engine idle down and shift again. This worked most of the time. I did some research and found that some have modified the shift linkage. The problem with just adjusting the shift cable is that it really NEEDS more throw, not an adjustment. From what I've read and viewed on the Internet, the linkage arm needs to be about 3/4" longer to gain more throw in both directions. On YouTube, the guy had to remove the shift linkage hole trim and notch the side of the dash to get the shift linkage off the pivot pin. BUT this is NOT necessary. When the "E" clip has been removed and you fish it out of the firewall somewhere, the shift lever is now loose. I had to pop the top of the shift knob off, remove the retaining screw and then heat the lower portion of the knob to get it to come off the lever. Once you have the shift lever loose, push it towards the right to slide it off the pivot shaft. But it won't come off just yet. Use a small pry bar/screw driver and slide the nylon flanged bushing out of the left side of the lever. This lets the lever slide off and get into a "loose" condition and it will twist and come right off without removing the dash trim, that could be a bugger to get back on correctly. Once the lever is off, press out the other bushing so when you're welding on the linkage arm, you don't melt the bushing. I found a piece of scrap metal the same thickness as the lever arm, just over 1/8" thick, close to 3/16". I cut my arm and beveled the edges for better welding. I added a piece just over 5/8" long and kept about a 1/16" gap between the arm and the new piece. Once welded on bother ends, it adds up to just about 3/4" or so. I reinstalled the lever after painting it and did an adjustment on the cable. By the way, it's easier to remove the cable from the bracket on the frame. This gives you more clearance to maneuver in that area with your hands. ALSO, you will need to get a 12" adjustable wrench and slide it over the cable mounting bracket and tweak, to the front, the steel so the cable is pointed upward a bit to now realign with the new longer shift arm lever. There's more than enough metal for the tweak and it will line up perfectly. I now bottom out the shifter on the transmission BEFORE I run out of throw on the shifter... I've tested it just a bit so far and it shifts much better with the longer throw. One of the Coleman authorized repair facilities said that he worked with Coleman to get a new part that's longer by 3/4". He's modified a few and it works perfectly for him. Just doing the cable will just short you on the other end. Here's some pictures of my modified shift lever etc.

I have come to the conclusion @Joe Toup must be one of the very best, most helpful members here!!! He has been tireless sharing his knowledge and expertise helping me solve a problem. I am sure I'm near a good solution thanks to Joe!!👍👍👍

There are actually 5 disc brakes on these machines. 1 for each wheel and 1 on the rear driveshaft for the parking brake. I've read several complaints of the parking brake one being too tight from the factory so I would check the cable and make sure there's a little slack when the parking brake is released. If that is good I would jack up each corner Individually and spin the wheel to listen for noise and feel for dragging. That should help pinpoint where the issue is.

anybody else getting spam /fraud private messages on here besides me? How do I report it? He calls himself Maria .under ORANGE 15 name.. wants to hook up in UTVs .. con artist in Pakistan probably.. Cant ADMIN block this crap ? geesh

Just looked at the Lowes add for that, pretty much looks like an MSU 500/700 that Hisun made for Massimo back then. Take a good look at the badging on parts to see who it's actually made by, my guess is it's still Hisun.

Its my 2nd day on this plat form. I'm new here in this community but in these two days I got some Premium recommendations. I was in search of these recommendations form the past few months. Thanks you so much for creating such kind of the community. Regards: Zeeshan Mehmood

Put 15 miles on it today mostly on the beach in 4WD--the front diiferential is definitely smoother and quieter, and engaging/disengaging 4WD and front lock more positively with the ATF...

So how can i fix my UTV? " we'll circle back"

For a 16 digit PIN/VIN, the 9th number indicates the year. Hence, in this case, the OP's RTV is a 2006. Which is the same year as y RTV:

Waiting for snow.....

Finally delivered today!!

Got it home!

They got ours delivered today (instead of tomorrow).

My dealer just got parts this morning (purchased on Jan. 20th) - I should have it by the weekend!

I've seen a number of requests for the location of all the grease points on these machines, and there is no definitive list in the manual. This covers the UT400, but other Coleman/Hisun models should be similar. Tools: First to grease your machine you need a grease gun and some NLGI#2 grease. You will find it helpful to buy a needle attachment as pictured here, due to poor clearance on some of the U-joints. The rest of the zerks use the standard attachment. Technique: Wipe any dirt/grease off the zerk before greasing to prevent pushing gunk inside and causing excess wear. Push the grease gun on the zerk at a straight angle and give it a few pumps. You will hear an oozing noise or sea grease coming out from the outside of the greased area when you've put enough grease in, a few pumps should be plenty. If it's just oozing around the zerk you either don't have a good seat with the gun, or the zerk may be rusted and the check ball frozen. Try seating it again and regrease. Wipe up any excess grease when youre done to prevent making a mess. Greasepoints: Rear A-Arms are greasable with the wheels on from the rear, I took the picture with the wheel off for easier visibility That's it. All other Hisuns should be substantially similar.

happy new year!

Hello Everyone Brand new Joyner CV AXLES are waiting to be unloaded at LA port and then be sent to warehouses in Charleston, TN , BALTIMORE, MD and Groveport, OH. Estimate they will be available for shipments to end customers in about 2-3 weeks. These CV AXLES are ordered in February this year and now it is middle July. Very long time to get these parts. Qty for each model is not big. Detail as below: S/N Part No. Description Charleston, TN BALTIMORE, MD Groveport, OH Total 1 D650.03.02.02.00 650 Sand Spider Rear left 3 2 3 8 2 S650.03.02.02.00 650 Commando Rear 7 6 10 23 3 TR1100.03.01.03.00 TR1100 Front 3 3 4 10 4 D650.03.02.03.00 650 Sand Spider Rear Right 3 2 4 9 5 S800.03.02.02.00-R2 800 R2/4 Rear Shaft 4 4 6 14 6 TR1100.03.02.03.00 TR1100 Rear 6 5 9 20 7 S650.03.01.02.00 650 Commando Front Left 3 3 4 10 8 S650.03.01.03.00 650 Commando Front Right 3 3 4 10 Below items are also available. These items can be shipped in days CAGE: 1. 800 Renegade R2/R4 Front outer cage --- 5 pieces 2. 800 Viper SV1100 Drive shaft rear Left outer cage --- 5 pieces 3. 800 Viper SV1100 Drive shaft rear left inner cage --- 3 pieces CV BOOT: 1. 650 Commando Left Front / 650 Commando Right Front /650 Sand Spider Rear Left / 650 Sand Spider Rear right / OUT CAGE 2 pieces 2. 650 Commando Rear OUT CAGE 1 pieces 3 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE 2 pieces 4 650 Commando Left Front / 650 Commando Right Front INNER CAGE 1 pieces 5 650 Sand Spider Rear Left / 650 Sand Spider Rear right INNER CAGE 1 pieces 6 650 Commando Rear INNER CAGE 1 pieces 7 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE INNER CAGE 2 pieces Anyone who need above items please contact me at [email protected]. Thanks. Other Joyner items needed, you can also contact me and I will try to help. Have good day Casey / Leaf Asia 2021-07-20

after all the complaints on this forum about the other brands of utv's, i will stick with my mule...........not the fastest, not the most powerful, but it hauls stuff around the house and plows snow just fine..........

Paint chip is no good, but doubtful that it made it thru the filter, so it's likely been there, or got knocked off when you were working on removing things. Code 201 indicates that it is getting a weak or unexpected signal from the injector. The fuel metering is done by pulsing the injector open. The ECU expects it to be X resistance and it gets Y resistance instead and throws a code. This could be a failing injector (the internal solenoid may be failing) a loose or intermittent connection, chafed wire partially shorting to ground, moisture or corrosion in a connector, etc. It's likely intermittent, but will eventually get worse. When it's happening it will throw the code and give the engine the wrong amount of fuel causing stalling, performance issues, no start, etc. If it were me I would visually inspect the Injector wiring for chafing, check inside the connectors, and if I didnt find anything just throw a new injector at it. You can also check resistance of the injector, but if it's intermittent it may check out ok when you happen to check it.

Thanks for taking care of the spam, UTV Board Admin.

To get the proper break-in I get it. I tend to agree

My mother is a hard worker. She's 91. Lately the pain in her legs is so bad it's keeping her from working as hard as she wants. She lives on a 20 acre ranch in Black Forest, Colorado. It's bad enough sometimes she can't walk back and forth to her front gate which is about 100 yards each way. Working hard is her joy in life and she recently broke down crying to my daughter talking about how she feels limited. I want to get her a UTV, soon. She's pretty little only 100 pounds. Money isn't really an issue. This is Colorado and her ranch is at 7500 above sea level so snow is always a factor but with the sun and our atmosphere being so thin snow melts pretty quick. Still I want 4WD as an option or fulltime. I want entering and exiting easy, She doesn't need ground clearance. She will never go trail riding. I'd like to have an enclosed and or removable cabin and heat if possible. Easy start up and do they all have clutches? No clutch or a very light one would help. Some kind of a bed for gardening would be good. That doesn't have to be heavy duty. We're not hauling wood. We have a Kubota tractor I can use for snow plowing. This is just a runabout for the ranch. Even electric would probably work. I don't think we want some no name Chinese thing. I'm around and live about 15 miles away but I can't be there 24/7. We watched a video about Polaris UTV 570 but that's the only video we watched. I frequent other board like those about muscle cars and we're always wary about first time posters especially if they're selling something. I'm not selling but I am a serious buyer and I'm trying to move rather quickly on this. Thanks, Steve in Colorado.

I have had mine since 2019. Don't have many hours on it. I purchased it from the factory in Texas. It was an auction. When it was delivered, the roof was missing. Apparently it broke and blew off in transit. The driver refunded me $200.00. The next morning I contacted Massimo and advised them of what happened, and was fully prepared to purchase another roof. This was a floor model, so it didn't have much of a warranty. Much to my surprise, they sent out a new one free of charge. I have also had some technical questions, and one of their techs has been very helpful with wiring diagrams, tech advice, etc. I know that hasn't been the case with some owners, especially those who bought their machine through Tractor Supply. Apparently Massimo has not been prompt with warranty reimbursements with repair shops, causing most shops to refuse to work on them. Believe me, I get that. Maybe this will all change, especially if they want to step up their sales and service. I just wanted to say that I have been fortunate to have good encounters with the factory. Sent from my SAMSUNG-SM-G891A using Tapatalk

Do a little reading here on the forums and you'll find lots of issues with the Hisuns from that time frame like mentioned above. I passed on a '16 with fewer miles for the same price.

Go to Engine Coolant Sensor on top of the head.....will look like a mini spark plug. Single wire. This runs to ECM. The sensor is a special resistor that changes resistance value.....most are NEG....meaning the value goes down as the probe end in the coolant gets hotter....and of course the reverse also for R high at low temp. Test time DVM DC VOLTS. Pull and probe the ECT plug....KEY ON. You should have +5 ish Vdc....source is ECM signal input that has an INTERNAL resister in series to +5 source. The DVM "sips" current....thus NOT A LOAD. Next....DVM R range. N to head body and P to sensor tip connection. You should have some resistance (don't have specs) say cold 10K to 100K. An open sensor pellet will be INFINITE...same as leads apart.....which is bad. Your message stated the Error Code was high voltage or open circuit. With out a load....Meter doesn't count.....you get +5Vdc from ECM at ECT sensor connecter. If ECT is good (a resistance load) AND wiring is good, the voltage will be less than +5 due to voltage divider action. The changing sensor will change the inputs voltage....calibrated to temp to control fuel delivery.....Like the TPS, a swing from 1V to 4V. That's how it is supposed to work. Your problem is one of 3 items harness/connectors/ECT. If no +5 at connector, check at ECM....if good, find the open ckt. The open circuit makes the ECM think it is at the South Pole @ - 40 deg C....dumps extra fuel for a COLD start. Check spark plug for sooty black or wet electrode....clean and dry or start with a fresh plug because fouled plugs may look sorta ok, but no or weak spark. CHOW

Here's a couple shots of mine--I had to "re-brand" it as an LSV (Low Speed Vehicle) to make the State of Florida happy (they had to do a physical inspection, I figured it would not hurt to badge it as an LSV) and get it registered: (made it into an "Outfitter LSV" with 3D printed badges--just used that gray 3M double-sided tape to stick the low-speed placard on; we had just been calling it "the thing"--"Thing 1" was what my great-granddaughter thought it should be called. I thought "Thing 16" as it's a "4x4", but my wife said no one would "get" it... I have a thread re: the Briggs muffler/cheap noise reducer--works great with the end-cap perforations opened up to 5/32" (from 1/8" OEM, a 56% increase). Took it off a few days ago, just made it louder--no power change at any RPM--put it back on to make myself less obtrusive... The flag decal is the "Bonnie Blue Flag"; of the Republic of West Florida and an early flag of the secessionist States during the War of Northern Aggression.

View File Coleman HS400 3D printed parts Here are a few little parts I made for my new coleman 400. One is a dummy seat belt clip to make the speed limiter think a belt is engaged (for diagnostic purposes only, do not ride without your seat belt on.) Another is a replacment for the circular grommets in the front corner of the bed. The last is a replacement for the rectangular cap at the rear of the frame near the hitch. Parts may need a little sanding depending on your print settings. Enjoy! Submitter tsheh4 Submitted 04/16/2021 Category Coleman  

Sounds like the P.O. was a textbook example of what we used to call "Fast & Furious Magazine Mechanics"(FnFMM)--more money than engineering, or even common, sense. Bigger wheels an d tires do nothing but: Reduce power to the ground due to their larger diameter; Reduce braking power due to 1); Reduce acceleration due to 1) and increased weight = increased rotational inertia; Increase wear of drive train components (CV-joints, U-joints, transmission and final drive gears and bearing, etc) due to 3);. Worsen "ride" quality due to increased unsprung weight; Overload suspension components (spring struts, A-arms, ball joints, tie-rod ends, steering gear, etc.) due to increased mass/altered geometry; Mess up the speedometer and odometer¹ by making them "read" slow; Huh, seven sins--I really did not set out to do that. But they "look cool" and will make your fellow FnFMMs envious--all while making your wallet lighter, We have already seen (literally) what a "lift kit" can accomplish so I won;t get into that... Contrary to what the average FnFMM thinks, the emgineers that design these things do generally know what the are doing,,, ---------------------------------------------------------------------- ¹ - the odometer thing mat be "good" if you are planning on screwing over a buyer down the road (no pun intended). Let's suppose you put 27" tires on a vehicle designed for 25" tires--that's an 8% increase in circumference. So, the 5,000 miles you put on the vehicle will be recorded as only 4630 miles.

I just changed the gear oils in my 2020 Outfitter 400 a couple days ago--used Supertech (Walmart's house brand) 75W-90 GL-5 gear oil, which is made by Valvoline--Its what i used it in my 2003 515 HP 2003 Mustan g Cobra, thatr's why there was a nearly full bottle on the shelf in the barn..--use it in my 2009 Honda Silver Wing too. Heck, I'd use it in anything without hesitation...

My maternal grandfather (a Scotsman ME) always told us that "...the last time any machine started and ran properly may well have been the last time it will start and run properly." Also, "God created men and they are imperfect--men created machinery, so guess what that makes machines."

sometimes that can be a sign of an ignition system part failing.. i'm not up to speed on the Massimo ignition systems as to if there magneto and flywheel fired, or CDI off of battery. had a similar issue with a car awhile back, run and get warm and shutoff, wouldn't restart for awhile until cool. turned out to be the ignition coil. after it dies i would check for spark, either by removing the spark plug and reinstalling the wire and grounding the spark plug against the engine and looking for spark, or by removing the plug and spraying carb/parts cleaner or starting fluid down the plug hole or intake.

Yo fun-knee

Wow, this is another obstacle that may hit me one day? Mine is a 2019 too and was brand new when I bought it, 30 days later it was in shop for a month, they said it was a drivers side seat belt safety issue, I was told that they replaced the seat belt assembly and that cured the problem, come to find out, they did not replace anything. I returned to dealer to look at their work order on it and surprisingly they lost that work order. In other words.., they lied. Took it to a local mechanic and he fixed it within an hour. Clogged injector, blew it out and it ran great for about a month, then same issue, I pulled injector, blew out the port and injector and runs great again for about another month, called local mechanic for any advice and he told me to run premium fuel, higher octane and see if that helps, that was several months ago and it’s been running flawlessly so far! Sounds like you having same issues, might try higher octane and see if it helps???

If a pickup tube in the gas tank were disconnected or maybe cracked, that could explain why the engine quits after the fuel level drops (to a point where the fuel pump is pumping air). The fuel pump draws fuel from the bottom of the tank. But that doesn't explain why the engine runs if you hold a little accelerator pedal. Is the fuel tank vent tube plugged somewhere between the fuel tank and the charcoal canister? Remove the fuel filler cap to see if a vacuum in the tank is causing a loss of fuel supply. Is the carburetor getting adequate fuel?

A mule is supposed to be better dressed. Should at least have a hat on.

Hi sir, welcome. I found the part number for the alternator and it plugged it in at Kawasaki, the 4010 won't cross over with 3010 I did find this one on EBay, https://www.ebay.com/itm/kawasaki-oem-part-21001-1129/264725199503epid=1223129455hash=item3da2d9fa8fcolongcolon7agaaosw6xxevejkredirect=mobile

I went to visit a man and his wife today on their farm and they had a Kubota side by side there. There was some coveting going on at that place!! I convinced myself that if they made a gas version, I’d buy it.

eHello all utv s by s owners! Preferably Seeking HISUN owners to help me keep my favorite utv running tip-top!