Quantcast
Jump to content

ERV JR

Members
  • Content Count

    161
  • Joined

  • Last visited

Community Reputation

0 Neutral

1 Follower

About ERV JR

  • Rank
    Advanced Member
  • Birthday 11/12/1981

Profile Information

  • Gender
    Male
  • Interests
    Drag racing, boating, riding on and offroad

Contact Methods

  • Website URL
    http://
  • ICQ
    0

Recent Profile Visitors

3,040 profile views
  1. ERV JR

    Diff upgrade help

    Ah man now the direction come out, too late for me. The lousy part was I spoke to Silver bullet and he said he had never heard of anyone shimming the spider gears. I had planned to do that just like I do in other diffs. I sorted thru my shims and found what was need to shim the pinion but didn't see any shims behinde the bearing on the carrier to tighten backlash anymore. Now I wish I just went with my plan and shimmed the spiders. I could have ordered plenty of shims. It is better but not ideal. Hopefully it lasts another few years an I can reset up as I'd like later. Bad thing is I tigged the spider gear shafts to the carrier as per Silver bullet but I could easily dress the weld with an endmill and pull them out Sent from my SCH-S968C using Tapatalk
  2. ERV JR

    Diff upgrade help

    Its together and sealed uo Sent from my SCH-S968C using Tapatalk
  3. ERV JR

    Diff upgrade help

    Jeff I didnt find any instructions. I cut the bokts to legth and shimmed the pinion to sit as deep as possible. I realized why these diffs break. They are junk. Lol . I can't shim the carrier to adjust back lash. Well without maching the case to allow for the carrier to move Sent from my SCH-S968C using Tapatalk
  4. ERV JR

    Diff upgrade help

    I will probably throw several in the vice on the mill and cut the head on the mill Sent from my SCH-S968C using Tapatalk
  5. ERV JR

    Diff upgrade help

    Ok guys I tore my diff apard anfrer shearing the ring gear bolts. Drug my butt after rearing it down, yesterday while placing a McMaster Carr order I searched the board for the part number and added the bolt s to my normal order. They showed up this morning and I realized they are long , really long. I grabbed a set of calipers and mic'ed the carrier and ring gear and come up with about 16mm in length. So the question is why in the worldvare the bolts that folks talk about 40mm long ? Are you guys ordering them long so that they have a shank at the top where they go thru the carrier & cutting them off ? Sent from my SCH-S968C using Tapatalk
  6. ERV JR

    T2 Light bar width

    Thank you very much Sent from my SCH-S968C using Tapatalk
  7. ERV JR

    2014 Joyner R2 Differential

    What are you putting nuts on Sent from my SCH-S968C using Tapatalk
  8. ERV JR

    T2 Light bar width

    So any help would be great Sent from my SCH-S968C using Tapatalk
  9. ERV JR

    T2 Light bar width

    Can anyone pull a tape between the factory lightbar mounting tabs Sent from my SCH-S968C using Tapatalk
  10. ERV JR

    Rear diff help

    Well I pulled it apart and got lucky. Just sheared the ring gear bolts Sent from my SCH-S968C using Tapatalk
  11. ERV JR

    T2 Light bar width

    What's the width of the tabs on a stock cage ? Also maximum width of the main hooo before the bend ? I forgot measure this weekend, troopers 250 miles away and was too busy pulling the diff before I left Sent from my SCH-S968C using Tapatalk
  12. What size rims? And brand Sent from my SCH-S968C using Tapatalk
  13. ERV JR

    Rear diff help

    Well I'm hoping I didn't chip the ring and pinion. By rotating the drive shaft I can see the ring gear turning and I don't feel any rough spots. Nor do I hear any noise when it put it in gear Sent from my SCH-S968C using Tapatalk
  14. ERV JR

    4x4 actuator

    Is there a conversion kit to make it manual and engage with a cable ? Sent from my SCH-S968C using Tapatalk
  15. ERV JR

    Rear diff help

    It appears that I sheared all the ring gear bolts off. I removed the fill plug and I can either push the trooper or rotate the driveline and I can see the carrier rotate separately frim the ring gear. With that in mind what are the odds that the ring and pinion are in decent shape and I can extract the broken bolts. Worst case possibly tig weld a nut or bolt to the broken bolts and . Also who sells the shim /upgrade kit ? Btw inorder to pull the diff do I unbolt the upper part of the spindle and let thw spindle fall to get the axle out ? Sent from my SCH-S968C using Tapatalk
×