Jump to content

  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • dump bed problems

      I have a 2003 Kawasaki Mule kaf620-e3 my dump bed doesn't work, just makes a clicking nose when I flip the switch. Any ideas out there. It is connected to battery and machine starts fine so not the battery.

      By marypippin14, in UTV General Discussion

      • 7 replies
    • Finishing the Small Items/Problems on Project Jeep

      One of the problems that kept us from taking the Jeep with us was my Jeep was leaning on the left side (lower on the driver's side) after everything was mounted; New tires, new wheels, new leaf springs, new shakles & new diffs. It also caused the Jeep to dive on the driver's side when you turned quickly towards the right. I couldn't find the cause and I was under a timeline, time was running out. I was too reactionary! While traveling and upon the return home, I told myself to slow down, think and measure. I have fixed stuff like this before. So today I took the time to measure and just lay under the Jeep looking at the frame. Inch by inch comparing left side to right side. THEN, I SAW IT! The frame supporting the front spring hanger on the rear diff on the driver's side was bent. I took a floor jack and lifted the frame at the location aprox the amount of the bend and sure enough the Jeep was nearly level. In one of my shops when I poured the floor I installed tie-downs in case I ever had a problem like this. I will tie her down, jack her up until the bend is gone. I will then box both sides so this can't happen in the future. Must have happened when the right rear axle came out on the previous owner. I never saw it as the axle was hanging out when I bought her. At any rate it is a good day when you solve a problem! rocmoc n AZ/Mexico

      By rocmoc, in All Other Off-Road Toys

      • 8 replies
    • TNS 650 at Transmission Problems

      Hey guys   I have a TNS VN650 utv. I bought it second hand and not running. I manage to get it running now. But it does not engage the automatic gearbox. It show E1 ER error on the gear display. The solenoids do move the selectors as soon as it is switched on. But then nothing happens. Please i could use any advice.

      By Hannes, in UTV General Discussion

      • 0 replies
    • Polaris EPS problems??

      I recently owned the 2015 Polaris Ranger crew 900 eps , absolutely a wonderful machine never had one problem , just sold it , then upgraded to a 2017 1000 crew EPS, right off the bat took it off the trailer the EPS light came on which makes the electronic power steering not work at all , Took it back to the dealer as soon as I could they said they changed out a speed sensor took it home did the same thing took it back they changed out a relay switch kept it for a week looking it over to make sure didn't come back on then eight days later I got to take it back home with me and the light came on again , as soon as I noticed the light I loaded it up on the trailer took it back to the Polaris dealer light was still on when I got there they put it on the machine or computer said that two codes came up that the electronic power steering unit was junk theyd have to replace it , Service guy was super nice and very polite but the owner and the guy that sold me the machine (the salesman ) were very rude will be the last machine I buy from that place

      By Iowarider37, in Polaris UTV SxS Forum

      • 0 replies
    • Joyner trooper breaks problems..

      Has anyone replaced there brakes with something different..??? I only have 2 calipers working.. I bought two new master cylinders and still the same problem.. I'm only getting pressure out of one master cylinder.. I have bled them like 5 times and still nothing..     Sent from my iPhone using Tapatalk

      By Tobie1987, in Joyner UTV SxS Forum

      • 3 replies