Quantcast
Jump to content

Electrical Issues

DevilDog

By DevilDog
in Joyner UTV SxS Forum

 Share

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Kinarfi Veteran

Kinarfi

Posted
Posted

Key on ,I get nothing on any of those pins???

find that 2 amp fuse, or at least that's what the schematic says,

The key is in run, not just on, right?, are your gauges active.

My nest step before tearing wiring harnesses apart would be to pull every fuse and test it and reinsert it, undo the connector plugs under the computer (there's 2 of them) and inspect and reconnect, one the ip wiring connector and the other is the body wiring connector as shown on page 55 of the TR1100 -T2 -T4 manual 2008.pdf manual.

kinarfi

Link to comment
Share on other sites
Kinarfi Veteran

Kinarfi

Posted
Posted

Devildog,

I was looking through some of my drawings and found this, 2441466080104110397RTTmFT_th.jpg, go forward and backwards from this drawing and take a look at it and see if it helps, yours being a little older may it incorrect, but it does have the fuses numbered and the wire colors and it looks like there may be 3 fuses for the ecu, power, one for the normally open outputs and one for the normally closed outputs. It may be that some of this even came from the 2009 schematic.

Link to comment
Share on other sites
DevilDog Enthusiast

DevilDog

Posted
  • Author
Posted

Devildog,

I was looking through some of my drawings and found this, 2441466080104110397RTTmFT_th.jpg, go forward and backwards from this drawing and take a look at it and see if it helps, yours being a little older may it incorrect, but it does have the fuses numbered and the wire colors and it looks like there may be 3 fuses for the ecu, power, one for the normally open outputs and one for the normally closed outputs. It may be that some of this even came from the 2009 schematic.

Link to comment
Share on other sites
DevilDog Enthusiast

DevilDog

Posted
  • Author
Posted

Started pulling all wiring connections apart spraying cleaner and putting on dieelectric grease on and bam - One of the connector plugs going to the ECU was the problem, evrything works starts right up!!! Thanks for everyones help. Going for a short ride Sun ( not to far from the truck) see if its fixed.

Link to comment
Share on other sites
  • 2 months later...
darrylsm Newbie

darrylsm

Posted
Posted

I know this post is a tad old , but I bought an R2 because of electrical problems related to the fuse box behind the passenger seat near the ECU. I had to make my own relay/fusebox set up temporarily , but I have ordered one from rick @ silver bullet in the mean time. Heres what I have learned about the ECU harness and rear fuse box setup.

I cut the wiring , yes all of it. It was badly burnt and unrecognizable.

As far as the fuse box is concerned Basically there are 3 negative potential outputs , those are what turn on the fan , fuel pump , and main relay.

There are a couple of wires that are fused , and run to the ECU , one is on all the time , the other keyed.

The rest of the wires feed the gauges , the coil packs , and injectors , there could be some more , but the detail escapes me.

If your coil pack wiring has the proper + potential , as well as the injectors and computer. You can trick the computer in to starting and running. I bought 4 relays 50 amp from ebay , and a universal fuse box.

My renegade is running , and I do plan on repairing it properly when the harness/FB arrives , but I just thought id throw that out there , to let you know there is hope in making these engines run with the ECU. My first thought was to convert it to carb/distributor , but after a little wire tracing (very little thanks to the diagram) and loss of hope of conversion lol my renegade is back on the trails.

Link to comment
Share on other sites
Kinarfi Veteran

Kinarfi

Posted
Posted

I know this post is a tad old , but I bought an R2 because of electrical problems related to the fuse box behind the passenger seat near the ECU. I had to make my own relay/fusebox set up temporarily , but I have ordered one from rick @ silver bullet in the mean time. Heres what I have learned about the ECU harness and rear fuse box setup.

I cut the wiring , yes all of it. It was badly burnt and unrecognizable.

As far as the fuse box is concerned Basically there are 3 negative potential outputs , those are what turn on the fan , fuel pump , and main relay.

There are a couple of wires that are fused , and run to the ECU , one is on all the time , the other keyed.

The rest of the wires feed the gauges , the coil packs , and injectors , there could be some more , but the detail escapes me.

If your coil pack wiring has the proper + potential , as well as the injectors and computer. You can trick the computer in to starting and running. I bought 4 relays 50 amp from ebay , and a universal fuse box.

My renegade is running , and I do plan on repairing it properly when the harness/FB arrives , but I just thought id throw that out there , to let you know there is hope in making these engines run with the ECU. My first thought was to convert it to carb/distributor , but after a little wire tracing (very little thanks to the diagram) and loss of hope of conversion lol my renegade is back on the trails.

Take some fotos and send them to me and I'll add them to mine so they can be shared, especially if you find some new information and if you need help and I can give it, let me klnow.

One thing I did for powering up the fan and fuel pump was to replace the relays with high power FETs, NO moving contacts. I'll be looking at the main relay now that you have brought it to my attention. Died you say there is power to the ECU all the time or just to one of it's fuses. Did you download the Trooper wiring Diagram schematic in parts and pieces under manuals? Did a copy and paste of the PDF and created a drawing of the information 2486333090104282158CLzAXt_th.jpg

Kinarfi

Link to comment
Share on other sites
  • 2 months later...
iltrooper Rookie

iltrooper

Posted
Posted

I had a master switch problem. I store my T2 in a warehouse so when I was in there I would always start it and let it warm just to know all was well. For no reason one day it wouldn't start. It would roll over only. No spark or injector pulse, (checked with a GM noid) but dash cycled, fan cycled, lights and accessaries worked. Thinking ECM or at least crank trigger I towed it to my shop and started to check things. Why I did it I don't know, but I cycled the main kill switch and it started! Real RELIEF!

Link to comment
Share on other sites
  • 3 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • malenurse13
      American Landmaster TW450 Won't Start!!
      By malenurse13
      We just bought a used 2017 American Landmaster TW450. No hour meter that I can find, so not sure exactly how much it has been used. 
      The first 2 days we had it, the starter was a little sketchy, but it started after 2-3 tries. Sometimes when turning the key, we would hear a loud metal "clink" sound. Like the starter made contact, but didn't have enough power to turn. 
      THIS MORNING... Turning the key, we hear a single click sound. That's it. Even with a new battery, the starter is still doing the same thing. Both batteries (old and new) were reading 12.8 volts on volt meter. So I'm wondering what else could be going on? Any ideas on what to look for would be greatly appreciated...
      Thank you!
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • moonrover
      Coleman 2022 UT 400 radiator thermo switch replacement question
      By moonrover
      Mine is overheated/burned/melt at connection with its wire connector, parts are ordered to replace both them.  This seems to be a common issue, and some of you already replaced it. I right now just connect the wires, so the fan runs  all the time whenever the initiation is on, but it's better let fan runs as needed with a working temperature sensor/switch. 
      Question: Does some coolant come out by removing the switch/sensor from radiator?  Or, is the threaded hole all the way inside radiator?   If the answer is yes,  I want to drain or extract  some coolant to make its level below the sensor before replacing it, so I don't make a mess with coolant spilled out 
      Thank you.  
    • REDfletching
      Seriously considering buying 2022 Axis 700 from Lowes… any regrets from current owners?
      By REDfletching
      Spent today at a Honda dealership looking at their 520 side by side, then on the way home past our Lowes noticed they had several new UTVs on site, so we U-turned and ducked in there. We were impressed that all that came for $9,999 metal whole length skid plate, nice sized bed, roof, windshield, side mirrors, winch, upgrade looking tires… all of which would have added thousands of dollars to an already expensive Honda 520. Now Honda does have a great reputation from my trusted UTV experienced buddy, so it has that going for it.
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...