Quantcast
Jump to content

pauldroach

1997 Mule 2510 - need winch mount

Recommended Posts

Our neighborhood association was given a 1997 Mule 2510. I am trying to find a winch mount that will fit it so we can add a snow plow to it. I have tried Kawasaki dealer who called Kawasaki and was told to contact Curtis Industries who made the part for them but so far no luck. Is there a newer model Mule that I could cross reference to use for finding a winch mount to fit? Is there a universal mounting kit that would work?

Thanks for any info

Sent from my iPad using Tapatalk

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • Kawasaki mule submerged in water !!help.

      Any 1 with some good advice ,my Kawasaki 2017 mule side by side was submerged in water and now dead. What can i do ?  

      By Harry Thomas, in Kawasaki UTV SxS Forum

        
      • 9 replies
      • 882 views
    • Kawasaki 4010 (Gas) Revs/Puleses at top speed.

      Not sure I'm explaining that right. but,.. I'll start with some history.  I bought the 4x4 4010 mule with a bad motor.  I built the engine.  Bottom end up.  Fresh bearings, Pistons, etc.  Cranks up and runs with no issues.  However,.. doesn't seem to run faster than 20 mph and pulses at top speed like something is up with the governor.  It feels like its cutting back.  Climbing and pulling it seems to be fine,. It pulls hard and doesn't cut up.  But on the road flat out  Cuts back/Chugs/pulses/Revs.  Not sure where to start. Kinda tired of thinking about it. Any Ideas? Just a mention, I'm not trying to make it faster, just fixed.  25mph it good by me.  Hell,... for my purposes I'm fine with 20 mph as long as its' running properly.

      By brothaman, in Kawasaki UTV SxS Forum

      • 3 replies
      • 193 views
    • kaf620-e3 kawasaki mule side by side

      Hey all my mule runs great until it gets hot then  just quits. won't start back have to plug battery in to charge it up seems like the  battery doesn't recharge when it is running.

      By marypippin14, in UTV General Discussion

      • 5 replies
      • 169 views
    • 2018 Kawasaki Mule Pro MX LE vs. Cub Cadet Challenger 750 EPS: By the Numbers

      The Kawasaki Mule Pro MX LE and Cub Cadet Challenger 750 are two midsized Utility UTVs ready to be put to work. Let’s see how they compare – by the numbers. http://www.atv.com/comparisons/2018-kawasaki-mule-pro-mx-le-vs-cub-cadet-challenger-750-eps-by-the-numbers  

      By Travis, in Kawasaki Mule

      • 0 replies
      • 124 views
    • 2012 Kawasaki Mule 4000 Hood release latch cable replaced

      I have a 2012 Kawasaki 4000 Mule and the hood release cable is frozen and will not move. I want to replace the cable and have removed the fenders, hood, cargo box to access the cable. I finally had to remove the plastic dash far enough away so I could get a wrench on the nut holding the cable release knob in place. That's a lot of fun. I cannot remove the pin holding the cable to the release bar mechanism. Is that a force fit pin or what. There are no keepers holding it in place. Any suggestions on how to get the cable out? I can see why the previous owner never fixed it as you have to remove the whole front to get to the cable. I've tried penetrating fluids to make the cable work with no success. Your help is appreciated. Gerry C.

      By Gerald Clarendon Sr, in Kawasaki UTV SxS Forum

        
      • 13 replies
      • 260 views
×