Quantcast
Jump to content

Hi Guys


Paiute3

Recommended Posts

Thanks everyone.

I WAS down with a cold so have not been on the computer much.

Flatbed, we are both going in the same direction. What is the dia. of the paddles. I have been looking at 13.00 x 15 as the specs show the dia as 30". That would make it possible to run 4wd with a 30" tire up front, there are quite a few on the market now.

My attention at present tho is to resolve my blown shock issue.

Take care everyone,

rocmoc n AZ/Mexico

Has anyone thought about putting dual shocks on each side?

Cinda

Link to comment
Share on other sites

  • Replies 32
  • Created
  • Last Reply

Top Posters In This Topic

Replaced my blown shock and disassembled it. Not a bit of oil left in it, pumped it up with air and it all leaked out within 30 seconds. Not a bit of dampening in it either, just the resistance of the blown seals.

The Shock

Shaft size 0.865 Micrometer

Body size 2.00 Micrometer

Stroke 4.25 Tape measure

Center to Center 17 7/8' collapsed 22 1/8" extended Tape measure Corrected 9-2-08

The Spring

Length 14 7/8 Tape measure

Coil Size 1/2 Tape measure

Coil O. D. 3 3/8 Tape measure

Coil I. D. 2 1/2 Tape measure

16 coils

IT WOULD BE MY BET THAT A SLIGHTLY SHORTER (FOR TOPPING OUT) WOULD BE GOOD, PLUS, ONE WITH A BIT MORE TRAVEL WOULD BE VERY GOOD. JUST MY OPINION.

I had this on that other trooper hostile site

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Steve Toney
      Hello, my name is Steve and just signing up.  Bought my first UTV yesterday.  It is a Massimo T-Boss 550.  
    • By SafeSledBryan
      Hey guys! My name is Bryan and i am the owner and creator of Safe Sled. Not some crazy corporate backed recovery product, but just some guy with an idea. 
       
      4 years ago, I suffered 11 strokes, and am now 50% paralyzed on the left side of my body. I am unable to work a normal job anymore. I was working on the sled 2 years before this all unraveled. My wife told me to keep working on it since i was pissing her off staying home and doing nothing.
      I still plan on improving and implementing different ideas as the product’s revenue continues to grow.
      if the sled is appealing to you, please check out my website, safesledoffroad.com
      Safe Sled Website
    • By CBS
      Greetings from Southern Illinois. My name is Bruce and I currently have a Hisun HS550 Performance Rural King. I have had nothing but problems with this unit replaced so many parts of it and of course, it stopped working and will not start again for about the 3rd or 4th time since 2018 it only has a little over 500 miles and has cost me a bunch of money and headache and the Rural King where I purchased it has a repair man who is certified to work on HISUN but he charged me a little over $600 to repair it once back a few years ago and when I got it home after it being in his shop for over 2 weeks the thing worked for a very short time but when I went to start it the next day it was the same thing and they wouldn't check it further without me paying for service, labor, and parts and I went around and around with them and since there aren't any dealer service centers for Hisun near me and even most of them can't get to it for weeks to months and it could be at their shops for months as they tell me they have problems getting the parts needed from Hisun to fix these giant paper weights. Oh, and you can't buy a scan tool (code reader) Delphi 190121 unless you are one of their dealers and I can't find any other scanner tool that works with it except the Tiny Scan Tool which I purchased and it will work if I could find the correct adaptor cable and connector to connect the Tiny Scan to the diagnostic port on the Hisun HS550 Performance Rural King. Yep, I pretty much have been screwed every which way that can happen with this machine. I am disabled, have cancer, and am on a fixed income so I need help if anyone knows what the connector is called (type or part name) that will plug into the diagnostic port to get my scanner to work it is a 6-pin connector and I hear it only has to have 3 wires connected to it.
      Thanks 
    • By Oldman
      I installed a new GY6 150cc engine in a Bull Dog Pup 200 and when I put it in drive, it grinds for a second and then runs fine.  Works great when i place it in reverse.  Could it be from it idling too high?   Any help would be greatly appreciated.
      Thanks!!!!
    • By NicholasNWM09
      Hello Everyone,
      COOL NEW Product Alert! 
      A company called NEW Wire Marine or NEW Wire has Badass custom panels for UTV, Buggy/Hunting trucks. From Fully wired switch panels with laser etched rockers with backlights in 5 different colors, to just parts like voltmeters, phone, USB and 12 v chargers. Rockers can be printed, or custom laser etched rockers and they even have sleek labeled pushbuttons. They are a first-class company with a great knowledgeable staff and outstanding customer service. Switches are based on 12v or 24v circuits and they also have marine grade wire and connectors, which is perfect for waterproofing your system!
      Go check them out!
      Check out the websites : https://newwiremarine.com/ and https://rockerswitchpros.com
       
       
       
       



×
×
  • Create New...