Quantcast
Jump to content

HAWG_MAN

Hisun Sector 250

Recommended Posts

Hello there and hope you're having a great time with your new unit. As to the problem of having a trailer hitch, it has to do with where to mount it. As you have noticed, these units have a solid rear axles. Due to their mounting there is no frame area available to mount a traditional trailer hitch. I have had these units down to the chassis and there are really no great places to mount it to. The rear axle is exposed and does not have a housing. The swing arm is about your only option here. You would have to fabricate a bracket from one side of the swing arm to the other and that also perhaps has a strut in the center to attach to the swing arm as well for support. Then you might be able to bring it out rear wards and have your trailer hitch then. I happen to be a mechanical engineer as well so this is just my 2 cents. Is it impossible? no, is it available currently? no. Any good welder and fabricator can make it happen though. Probably some good ol 3/8" plate and you're there. As you can see from the pic below, not a lot of area to mount one to. But there are lots of mounting areas at both swing are to axle points. Matt

IMG_20160608_171650266.jpg

Share this post


Link to post
Share on other sites

Thanks for your input and I was hoping someone had something available, I am a Machinist of 45 years and can fabricate something that will function. I only have a small hitchpin trailer I need to tow. Thanks again

Share this post


Link to post
Share on other sites
On 4/28/2017 at 11:02 AM, strike250 said:

Hello there and hope you're having a great time with your new unit. As to the problem of having a trailer hitch, it has to do with where to mount it. As you have noticed, these units have a solid rear axles. Due to their mounting there is no frame area available to mount a traditional trailer hitch. I have had these units down to the chassis and there are really no great places to mount it to. The rear axle is exposed and does not have a housing. The swing arm is about your only option here. You would have to fabricate a bracket from one side of the swing arm to the other and that also perhaps has a strut in the center to attach to the swing arm as well for support. Then you might be able to bring it out rear wards and have your trailer hitch then. I happen to be a mechanical engineer as well so this is just my 2 cents. Is it impossible? no, is it available currently? no. Any good welder and fabricator can make it happen though. Probably some good ol 3/8" plate and you're there. As you can see from the pic below, not a lot of area to mount one to. But there are lots of mounting areas at both swing are to axle points. Matt

IMG_20160608_171650266.jpg

I made a Tow bar (3/8 x 3 x 13" Aluminum (2) pcs.req'd

003.JPG

004.JPG

006.JPG

007.JPG

Share this post


Link to post
Share on other sites
10 minutes ago, Travis said:

That a wood chipper? Were'd u get it at? @HAWG_MAN

Chippers Direct Online: Tazz K32 (3") 212cc Chipper / Shredder With Viper Engine has a 20:1 waste reduction very nice mulch best on the market @ $599. I have about 9 acres and lots of small limbs/leaves and have used it about 5 hours with no problems.

Share this post


Link to post
Share on other sites

Hi Hawgman

a question ..if you don't mind

where did you buy a NOS sector 250?.... And what did it cost, if you don't mind telling

thanks

John

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • Hisun Sector/Vector 250 Service Manual?

      I haven't been able to locate a Service Manual (aka Shop Manual) for the Hisun Sector 250.  Does anyone have one they can share with me?
      I have the service manual for the Strike 250 (thanks Strike250), but I'd like to have the one specific for the Sector/Vector.  Thanks!

      By DigitalDan, in Hisun UTV SxS Forum

      • 4 replies
      • 1,088 views
    • hisun sector 550

      Hello, I am looking to purchase a hisun sector 550 from a farm store, I am wondering who has one,and how reliable are they? I will just be using it around home,and to run down country roads.   Thanks

      By Kent Collebrusco, in Hisun UTV SxS Forum

      • 1 reply
      • 293 views
    • Strike or Sector 250 wheels and tire options

      Hey all, pretty pumped there is a forum for these machines. I see the stock sizes but does anyone know what size wheel/tire they can take? Example 24x8 or 26x8 ext? I understand it would need a new wheel and tease adapter to match the front,.   Thanks

      By CStrike250, in Hisun UTV SxS Forum

      • 1 reply
      • 110 views
    • Sector 750 Windshield fogging

      We have a new Sector 750 we use on a ranch in Southern Chile.  Very happy with the machine although the first oil change  was insane getting the filter off...  Obviously it is winter there and we are having a real problem with the windshield fogging up in the rain/cold.  I have removed it for safety  to be able to see.  Any suggestions as to how to prevent it or anti-fogging solutions to be used.   Thanks.

      By skyskidad, in Hisun UTV SxS Forum

      • 3 replies
      • 153 views
    • front axle for kubota rtv 900 2000 model

      Hello, I’m writing this because I desperately need some assistance with front axle for kubota rtv 900 2000 model. My stepfather told me his two front axles of his  kubota rtv broken separately yesterday and he couldn't distinguish which is for left or right. Are left and right front cv axles the same on a 2000 kubota rtv 900 4x4 ? And what's the cost of kubota rtv 900 axles ? I don't learn much about kubota rtv and hope someone tell me. Thank you.

      By matt wichert, in Kubota UTV RTV Forum

      • 1 reply
      • 184 views
×