Quantcast
Jump to content

Recommended Posts



Any kind of liquid, or anything that changes how those bolts slide against those threads will change how it torques. I've broken off bolts using a torque wrench while still within specs, when I lightly lubed lug nuts n stuff. Even anti sieze has caused problems for me in the past.

 

  My recommendation is make sure their completely dry, holes also, and just torque them down. You can't use less torque just because they're old bolts. And you sure don't want to take chances, with aluminum threads. So imho, that's the best way to be safe.

 

  Also, these bolts typically have a pattern that must be followed when torqued.

Share this post


Link to post
Share on other sites


'Bout to head out the Machine shop, Hopefully they can take the guides out. If they dont work, i've been talking with Power Toys of Texas, here in Cut n Shoot.

Pray for me!

Share this post


Link to post
Share on other sites

He shouldn't have any trouble,he's got all the tools, and experience. I wouldn't go up there till I could take new guides, let him install at the same time.

Share this post


Link to post
Share on other sites

I did! He said its a defect in the cast, and he ran it through a  vacuum machine thingy.

57 minutes ago, kenfain said:

Have him look at that crack

Ewww, Gross. 😁

Share this post


Link to post
Share on other sites


Once i get the new guides in Im going to back it back to take out the guides, and install them, He'll also re assemble the head too.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By Travis
      2019 KAWASAKI MULE PRO-MX
      MIDSIZE MULE™ MODEL JOINS KAWASAKI MULE™PRO SIDE X SIDE LINE UP
      Following multiple accolades for its MULE™ PRO series, Kawasaki continues to grow the MULE PRO family with the addition of the all-new MULE PRO-MX™ side x side to the 2019 lineup. The MULE PRO-MX features increased recreational abilities and rugged,no-nonsense styling that further establishes the mid-size, compact side x side as the customer’s dependable choice for work or play.
      http://www.utvguide.net/2019-kawasaki-mule-pro-mx/
    • By Travis
      I was reading a VS. article on ATV.COM, and they were doing a head to head  with the Pro FX EPS, and the Textron Prowler. And they said Kawasaki is using a  812 CC Chery motor for the Mule!
       Kind of surprised me, i thought Kawasaki used their own engines for the mules.
      🤔
    • By Travis
      Once i get the cylinder honed, the only remaining problem is the crankshaft shim..  And i have a few questions.
      1. In the manual it gives a solution to the problem i'm having of the crank NOT spinning when the cover on (by hand).
      2.  And i just can't wrap what's left of my brain around the instructions, i guess use a caliper to measure? (instructions  circled in red)
       (my brother has been helping me, he's fairly knowledgeable with this stuff, but more Diesel engines than anything) and he says to use a dial indicator set up, and to use this* as a spec for end play. and that would help us get the measurements needed in picture #2.
      1st pic is the runout. But is it the same as crankshaft end play? 🤔

      2nd pic is of the instructions (solution) to get the correct shim.
       I don't know, maybe this makes sense the way i wrote it.
       Thanks, Travis.
    • By Dan B
      I have a 2014 Joyner Renegade R2 1100cc.  I've seen many posts about these bolts sheering off.  I don't run my R2 very hard. I live in the desert southwest; not much mud around here.  I'm just wondering if I've got a potential of having the same problem or do these bolts only sheer off when running hard through deep mud and such.  Did Joyner realize this problem and include 12.9 bolts in later versions, like my model year?  Seems like this problem appears in the earlier model years.
    • By Travis
      My valve guides are un even..... they are the same size, just one sticks out farther.


×