Quantcast
Jump to content

  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By blissman20
      Hey guys, just to give you a bit of back story here first.  I used to ride big mud machines and SxS in the swamp.  Went through a divorce and lost almost everything.  What I got to keep was a snowmobile that I had for years and never rode anymore and wasn’t worth much to me so I decided to try trading it for more or less any UTV/SxS I could.  Well that landed me here, I just traded it for a 2008 Kandi KD650 which is a direct clone of the Joyner Commando 650.  The machine is in rough shape but runs and drives.  I have a few things to repair on it. (Seized choke cable, seized Ignition, and needs a voltage regulator). Going to to princess auto today to pick up a choke cable, and ignition, I have a voltage regulator from an old project that I will wire in.  
      The only thing I am wondering about is the rear end.  The guy I traded it for told me only one rear tire will spin when in 2 wd.  Is that the way all of these are is do  I need to rip it apart.  Also is there any aftermarket support for rear axles or axles that will fit that can be cut down and sleeved and rewelded.  Buddy there did some rednecking with a Polaris axle but not sure how strong it is. 




    • By dewillia
      I have a Joyner 1100cc Sand Viper in need of repair.  Does anyone know a repair shop or mechanic that services these in southern California?
    • By rh242603
      Hello-
       
      New to the forum so luckily there is some help out there lol. Recently bought a 2008 Joyner 1600cc sand viper and loving it. Took it out and had a little accident with a tree stump lol. The stump hit directly on my passenger side tie rod end and broke the heim joint that connects the tie rod end to the wheel. Does anyone know the size of the adjustable heim joint so I can order one? I am having a hard time sourcing one quickly. I am also guessing since it is an outter tie rod end, that it is LH pitched rather than RH? thanks for any help anyone can provide. This is again for the outter tie rod end heim joint that snapped. Thanks
    • By Dan B
      Disclaimer:  My spell checker thinks it knows more of what words I want to use than I do.  Typos are not my fault.
      This is a general comment on the support I received from Joyner-USA in Phoenix, AZ.  I needed one headlight assembly for my Renegade because the mounting pin was broken.  Duct tape and bailing wire held it in place for a few years.  To my surprise, they had them IN STOCK.  I bought two and kept one of  my good old ones as a backup.   They completed their move to a new address at 2415 S 18th Pl, Phoenix AZ from their former Riverside location.  As a gift, Jake gave me two T-shirts.  He said he as most of the parts for my  2014 Joyner Renegade.  I looked at his yard and he has several engines and UTVs in stock, mostly the 1100cc engines and several Renegades.  Maybe a Trooper or two was buried in there somewhere.  Everything was crated and outdoors.  I hope he moves his inventory indoors, out of the weather.  Their website says their hours are 9:00AM - 5:00PM but their actual hours are 10:00AM - 5:00PM.  I arrived at about 9:20AM and no one was there; place locked up.  I was a little upset that with a 9:00AM opening, someone should have been there.  I was concerned that I made a 70 mile round trip for nothing.  Fortunately, one of his employees showed up and told me of their later hours.  So, everything turned out fine.  I got the parts I needed and two T-shirts.  This is based upon a one time, 1st time experience.  I hope future vists are just as good.
    • By mixfixdave
      I had been wanting to install power steering on my T4 for years so I went to the salvage yard last weekend and bought a complete column (minus airbag) out of a 2009 Nissan Versa for $125 with the ECU.
      It was a fairly simple install. The long shaft that fits to the Joyner steering rack actually fit perfectly into the Nissan column. Had to weld up a U joint on the Nissan column to make it a straight shaft and fab up one simple bracket. Connect power and ground plus a switched 12v and now I can steer with one hand!

       


×
×
  • Create New...