Quantcast
Jump to content

Monty Herbold

2009 Joyner Trooper 5 Speed Transmission Shaft Size

Recommended Posts



Topic moved to Joyner forum and title changed to 2009 Joyner Trooper 5 Speed Transmission Shaft Size 😁

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • Wanted: Trooper Axle Parts

      I am interested in any old trooper axle parts you may have lying around. Please let me know if your want to sell them.  Backstory: Hey everyone. Last trip out to moab I climbed a wall on poison spyder Mesa while 2 rzr xp1000's and three can am x3 xrc's watched me and didn't dare try. After doing it once I pulled around to show them it wasn't a fluke. One on the can am x3 xrc drivers just looked at me and said "that's steep". On the second try I spread the bell on the left rear axle. I made the climb but now the inner cage slips inside making a loud popping noise as twisting the boot. I mainly just need the inner bell but I am interested in anything you have. 

      By 2scoops, in Joyner UTV SxS Forum

      • 0 replies
      • 66 views
    • Joyner trooper electric power steering for $200..

      I made my own electric power steering for my Joyner trooper..I bought a steering column out of a 02 satern vue for $80 at a junk yard..then bought a wiring kit off of eBay for another $80. And made the steering arm...the wiring kit even came with a adjustable nob..

      By Tobie1987, in Joyner UTV SxS Forum

      • 23 replies
      • 1,687 views
    • Joyner Trooper Power Steering

      I had been wanting to install power steering on my T4 for years so I went to the salvage yard last weekend and bought a complete column (minus airbag) out of a 2009 Nissan Versa for $125 with the ECU. It was a fairly simple install. The long shaft that fits to the Joyner steering rack actually fit perfectly into the Nissan column. Had to weld up a U joint on the Nissan column to make it a straight shaft and fab up one simple bracket. Connect power and ground plus a switched 12v and now I can steer with one hand!  

      By mixfixdave, in Joyner UTV SxS Forum

      • 0 replies
      • 103 views
    • Kawasaki 4010 (Gas) Revs/Puleses at top speed.

      Not sure I'm explaining that right. but,.. I'll start with some history.  I bought the 4x4 4010 mule with a bad motor.  I built the engine.  Bottom end up.  Fresh bearings, Pistons, etc.  Cranks up and runs with no issues.  However,.. doesn't seem to run faster than 20 mph and pulses at top speed like something is up with the governor.  It feels like its cutting back.  Climbing and pulling it seems to be fine,. It pulls hard and doesn't cut up.  But on the road flat out  Cuts back/Chugs/pulses/Revs.  Not sure where to start. Kinda tired of thinking about it. Any Ideas? Just a mention, I'm not trying to make it faster, just fixed.  25mph it good by me.  Hell,... for my purposes I'm fine with 20 mph as long as its' running properly.

      By brothaman, in Kawasaki UTV SxS Forum

      • 3 replies
      • 181 views
    • Piggyback ecu on trooper?

      Is anyone running a piggyback ecu on their trooper!I'm interested in a fuel controller! But one with a little bit more control then the electronic jet Set up they sell. I want timing control and more in depth fuel management!

      By Volkz VLOGS, in Joyner UTV SxS Forum

        
      • 0 replies
      • 173 views


×