Quantcast
Jump to content

Bchickness

4 point harness

Recommended Posts



Welcome to the forum Bchickness! 

Sorry , I can't really help since I live in mostly wooded, flat terrain, I don't even use the provided belts on mine. But I am interested in why exactly, someone would need a four point harness, in something that doesn't move all that fast? Mountain trails maybe? If so, then we're gonna have to ask for pictures. East Texas terrain is a little boring in that way. Mud, or swamp, is the most exciting thing I'm likely to encounter. Otherwise it's an exciting 7mph. all the way. 

In answer to your question though, I'd think that the rock crawling crowd would know. Personally, if I thought that I needed that much safety, I'd want a racing seat, with hard doors, and a net. 

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • 2016 Hisun 750 cab heater installed - $175

      I installed a Maradyne Mm-a1090002 cab-heater in my Hisun.  It was a fairly simple install with the most difficult part being to find the proper location for the heater body.  It has to be located so that the heater hose, etc is not blocked by OEM air filters, body frame, etc.  On my 750 Sector I determined that by centering the heater body a few inches directly below the gauge cluster worked perfectly.  The 5/8" heater hose comes out just to the right of the air filter tube. Since the firewall is plastic, I placed a large piece of stainless steel on the outside of the firewall for a backing plate.  I drilled a couple of 1" holes in the plastic firewall for my 5/8" heater hose and spliced them into the upper and lower radiator hoses. I spliced the upper heater hose into the upper radiator hose and the lower heater hose into the lower radiator hose.  No shutoffs, since I figured I could easily install them later if I need them.  I bought 8 ft of 5/8 heater hose and 8 - 1" hose clamps at the auto parts store.  Then I bought 2 pex tubing tees 1" X 3/4" X 1" at the hardware store to splice into the upper/lower 1" radiator hoses. The electrical is easy by running the black ground wire and red hot wire to the power supply (cigarette lighter) in the center dashboard.  By removing the power supply you won't have to drill large holes in the dash and you have the correct wiring needed to wire the heater switch.  I installed another power supply below the front of the bench seat in the middle.  I did that because it's easy for the driver to access and it was near the battery box for an easy installation. After I refilled the radiator overflow with anti-freeze, I pulled the Hisun's front wheels up on my trailer with the back wheels on the ground.  I did that so the radiator and overflow bottle were higher than the rest of the cooling system and any trapped air bubbles in the heater core would head for the overflow.   If that doesn't work, let it idle with the upper radiator hose clamped shut (needle nose vise grips) directing all the coolant towards the heater core to speed things up.  Remove the vise grips when the radiator fan turns on and then put them back on when it shuts off two or three times. I have about $175 invested for parts and heater for the project, and my heat laser reads 190 degrees when the heater is on.

      By Rangerider45, in Hisun UTV SxS Forum

        
      • 6 replies
      • 780 views
    • New Wheel & Tires installed!

      WOW, what a difference! First let me say I will have pics up soon, maybe tonight. Wheels are the 15" Visionwheel. Tire is Dunlop Radial Mud Rover, 31X10.50R15LT. They fit, I do need to make a small adjustment to the rear of the Front suspension to get full lock to lock turning. At present I have 3/4+ but there is plenty of adjustment in the supension to get full lock to lock. Everything else clears easily. Ground Clearance is now a full 13 1/2". Gearing, First gear is now more like a 50's pickup granny gear instead of the factory tractor first gear. First gear is usable! Plenty of low range remaining, but all gears are much more usable. I now cruise thu the neigborhood in 4th instead of 5th. I will have my better 3/4 follow me with the car to check speedo and top-end. My guess top-end is easily 70mph. Flotation on sand. I went down the wash behind the house where I would normally flip into 4Wd. Never came close to needing 4WD, stayed in 2WD the entire time. I was running the full 30psi put in the tires at the tire shop. I have since aired down to 20 in the front and 24 in the rear so performance should even be better. Standing Start performance appears to be as good as before or better. You can now use 1st or 2nd to take off from a complete stop. Needless to say, I could not be more pleased. The setup has met every one of my wishes & expectations. rocmoc n AZ/Mexico

      By rocmoc, in Joyner UTV SxS Forum

      • 21 replies
      • 3,845 views
    • Quartzsite & Rocky Point

      First day of riding and no problems. Really easy ridding, only one hill was a little challenge. We rode the area Northwest of Quartzsite. All rock & dirt. Trooper operated GREAT! rocmoc n AZ/Mexico

      By rocmoc, in Joyner UTV SxS Forum

      • 20 replies
      • 2,585 views
    • 2008 Polaris RZR Voltage Regulator Relocation Harness

      Charging issues solved with voltage regulator relocation Have you noticed your battery light blinking on your 2008 Polaris RZR? This alarm is telling you that the battery voltage on your RZR is too low. You would think that with a 500W stator that the RZR would have no problem keeping everything running. But even with no accessories and just the factory headlights and cooling fan on, many owners have encountered low voltage issues with their 2008 RZR. One main reason that causes this problem is your voltage regulator. The voltage regulator is designed to automatically maintain a constant voltage level. In doing that work, the regulator will generate heat. Your voltage regulator needs to stay cool to properly charge your battery. 2008 RZRs have a problem with keeping the voltage regulator cool because it is located under the driver's seat. Once the regulator stops working, any power generated from the stator will not reach your electrical system and the battery voltage will drop. Then the battery light on your dash will start blinking and it is just a matter of time before you are stranded. Polaris solved this problem on the 2009 RZRs by moving the voltage regulator up in front of the radiator. Now you can do the same thing on your 2008 RZR without cutting any wires! Our wire extension allows you to move your voltage regulator from under the seat (no air flow = overheating) to in front of the radiator just like Polaris did on the 2009 models. This is a 10 1/2 foot long extension, using the correct Packard/Delphi connectors and terminals and assembled with correct Packard tooling. The harnesses will be made using high quality Cross Link Polymer wire and covered in high temp, flexible woven loom. This harness allows you to disconnect the voltage regulator on your 2008 Polaris RZR (under driver's seat) and relocate in front of the radiator like you find on 2009 RZRs. November 19, 2008 - Autotrend is currently taking pre-orders for first-run of this harness. Price per unit for this run will be $48.95 plus applicable tax and S&H. If you'd like to reserve a harness, use the email link below or call Autotrend directly. Name, address, phone number and C/C number are required. Credit card will not be charged until harnesses are built. Please note that you will need a bracket to mount the regulator up in front of the radiator as shown in the 2009 RZR photo above. You can order a bracket from your Polaris dealer - Part # - PL5252587. Autotrend EFI Telephone: (530) 642-0999 Email: [email protected] Website: http://www.autotrendefi.com/ More details: http://www.autotrendefi.com/rzr_regulator_harness.html More information regarding the voltage regulator issue for 2008 Polaris RZRs can be found here: RZR voltage regulator - PRCForum.com
      RZRS voltage regulator VS RZR 08 - PRCForum.com
      Relocating the voltage regulator - RZRForums.net
      View the full article

      By UTVBoard News, in UTV News and Information

      • 1 reply
      • 3,397 views


×