Quantcast
Jump to content

Recommended Posts

working on a friends2018 hs500 with 9.5 miles.it starts good but when you give it some gas it cuts out.you can let off a little bit and it keeps running.

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • 2018 HISUN HS500 Wheel spacers Hisun HS500

      Can anybody tell me where I can get wheel spacers for a Hisun HS500?  What other spacers will fit the hisun? Also, will 27-inch tires fit without rubbing? HELP!

      By Mark Floth, in Hisun UTV SxS Forum

        
      • 1 reply
      • 99 views
    • Hi from Mid-Michigan - working on my first UTV

      Hello all. I've spent a bit of time fixing various ATVs but am into my first UTV. My son actually owns it and I'm trying to help get it usable. He bought a 2014 Coleman Outfitters 400 4x4, it's actually a Hisun 400 4x4 UTV.  It has a 2004 Kodiak 400 4x4 motor in it and we have a wiring nightmare. Hope to be able to offer help here and there and seek it for my own project. Take care and we'll be in touch.

      By res2fr, in New Members Area

      • 2 replies
      • 157 views
    • On eBay street legal velocity predator x18 no reserve bidding starts off at $1

      Safer than any utv street legal chevy evotec must see  Start 2018 off with this Currently listed on eBay no reserve bidding starts off at just 1 penny
      https://www.ebay.com/itm/122873672785       602-326-3936       sandrail dune buggy street legal sand rail jeep car truck rzr turbo can am sand rail walker king fox 092 fortin                             091 Polaris Yamaha yxz Fox walker Evans Vw Manx x3 turbo rzr buggy mendeola sand rail off-road Sandrail Vw

      By Fireman2343, in UTV Off-Road Classifieds - Buy & Sell

        
      • 0 replies
      • 661 views
    • Mule 550 Starting Problem only after running

      Hello All, thanks for looking at my situation. I am new to the UTV world, but not small engines. Hoping you can help and I thank you in advance for your support / suggestions. My neighbor gave me his old 550 mule, which needed some TLC. It is a late model 2003 or earlier Kawasaki Mule 550, not sure of the VIN as I cannot locate it, and then did re-paint / powder-coat it. However I was able to get the right new parts as they matched the old ones. I have replaced the entire electrical chassis wire harness (headlights to tail light) Brand new battery new starter relay same voltage regulator - not sure if this has failed - may need to test resistance battery reads 12.8 volts start and solenoid work note sure about the Neutral Safety Switch - I pulled it, (light green wire from harness attached) - what appears to be drop of oil on tip. After I take the battery tender off the Mule, turn the key it starts up just fine and runs well. After using it for sometime or letting it run, after I shut it off, it will not start again via the key. I turn the key and nothing, no clicking, dimming of lights, nothing. It is as something i is blocking the starter trigger wire. If I remove the starter relay and test for voltages I get 12 volts on 1 prong and about 1 volt or so from the starter trigger wire (red / black) - if I turn the key, that wire registers 12v. If I jump the blades and turn the key - it starts no problem / every time. This also works, with the starter relay plugged in, if I turn the key and touch the metal top of the relay on the chassis , you will here the starter clicking and engage and eventually it will start. I find this odd as it started this morning, cold with no issue. Is it a bad brand new relay? a bad regulator? the NSS? I am drawing a blank, I called a few guys I know over at the local power sports service center and they could not think of anything. Thanks for your help Mike

      By mtarallo, in Kawasaki UTV SxS Forum

      • 1 reply
      • 2,319 views
    • Getting it all running

      Hello. I recently bought a 2008 Sand Viper 800cc. I had issues with the starter so I had it rebuilt, however now I cannot remember how it gets wited back up. If anyone could, would they please inform me through a picture on how to reconnect the four wires I have here. Thank you.

      By Zehrungja, in Joyner UTV SxS Forum

      • 3 replies
      • 610 views


×