Quantcast
Jump to content

Dan B

Skid Plate Removal Joyner Renegade

Recommended Posts

Tried to remove my skid plate to access the engine oil drain plug.  The plug isn't near an access hole but located between two holes.  Can't get a wrench in to remove the plug.  Short of drilling a new access hole (which I'm seriously considering), has any one been able to remove the skid plate?  Seems to be a nut on the other end of the screw and there's no way I can access that nut.  They must have bolted the skid plate on before putting the engine into the frame.  Thanks in advance.

Share this post


Link to post
Share on other sites


Well, I did get the skid plate off.  Used a pry bar between the skid plate and the chassis. That kept enough friction on the nut so that my impact driver could remove the screw.  Now I'll have to find a way to attach it to the frame since the nuts are not accessible.  Probably will consider 6mm stove bolts and nuts if I can find any.  There is a large hold that is off center.  If the skid plate is installed incorrectly, that hole will not line up with the oil drain plug.  That is why I couldn't access my oil drain plug.

Share this post


Link to post
Share on other sites

they built the  renegade around the oil drain plug :D  

Share this post


Link to post
Share on other sites

But nobody told there where the drain plug was going to be until after they put the skid plate on.  I'll be looking for some U-nuts.  They'll be better at reattaching my skid plate.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By DJ530
      A few pictures (so far) of the engine work - eventually I will share wiring info and other details (if anyone is interested?)  should anyone else ever need to swap an engine in one of these. The replacement engine is a Harbor freight $750 special 670cc,  (lawn mower/industrial type lump) with a few minor upgrades. Should have it back together soon, bolted in. The cold weather slows me down! 




    • By Vernon Brown
      Has anyone done an engine & tranny swap on an 1100cc sand viper?
    • By KTMspeedFreak
      Hey Everyone, I’ve created a few other threads and a bit disappointed at the limited responses the forums seem to get. So rather than asking about an engine swap i’d like to share some information with others here in an effort to generate some discussion!
      So i’ve done much research on engine swaps for my 800cc buggy, and my ideal swap would be a suzuki swift gti engine, however they seem to be rare and very expensive if you can ever locate one. The only ones i’ve seen are going for $3500+ which is completely rediculaous becuase the purpose of an engine swap should be to get an inexpensive engine that parts are available for, the suzuki swift is neither.
      So in my research, i’m specifically looking for a naturally aspirated lightweight aluminum engine that produces “acceptable” power. Far as I can tell such a thing rarely exists in the US, which is probably why the G13b engines are so redicualously overpriced.
      What I have found, and present to you is a  Mitsubishi Mirage 1.2L It’s an all aluminium, lightweight 3 cylinder NA engine that’s producing 74HP and 74ft lbs torque. Not crazy power numbers I know, BUT for an NA 170lb readily available, AND cheap engine those are not bad in its stock form. Certainly those of you looking to get a little crazier than I can drop a turbo in and up those base numbers. 
      Far as I can tell in my research No one has done this engine swap to date, so I suppose I will have to go fist... I am not quite ready to take on a project of this magnitude but will likely make this my winter/spring project and hope to have it completed by early/late spring next year.
      I will of course document the install and process once it gets under way. In the meantime please feel free to use this thread to discuss other possible engine swap projects or ideas for such! I love me some buggy action and can’t wait to get this swap underway.
    • By Earl Middleton
      I have acquired an older Kawasaki Mule 2010 with KAF 540C engine.  The engine is shot so I have the option to either rebuild or replace.  I am thinking a swap to a three cyl diesel out of a Toro mower.  Anyone tried this?  The only reason I am considering this is because I have the mower which is inoperable.  The engine runs great so just wondering if this swap would be feasible?????
       
    • By johnpeter
      Polaris Ranger 800 11-16 4x4 6x6 Crew Engine Motor Rebuilt On Ebay
      https://www.ebay.com/itm/Polaris-Ranger-800-11-16-4x4-6x6-Crew-Engine-Motor-Rebuilt/361534749653?
       
  • Similar Tagged Content

    • By Volkz VLOGS
      Hi, I'm getting ready to supercharge my trooper and I'm looking for advice on the setup. So far I have... a AMR500 supercharger, small intercooler, Dolbeck EJK fuel controller and wideband. Looking for any advice on what else I'm going to need and what to expect..Thank you
       
       
       
    • By Volkz VLOGS
      Is anyone running a piggyback ecu on their trooper!I'm interested in a fuel controller! But one with a little bit more control then the electronic jet Set up they sell. I want timing control and more in depth fuel management!
    • By Dan B
      I have a 2014 Joyner Renegade R2 1100cc.  I've seen many posts about these bolts sheering off.  I don't run my R2 very hard. I live in the desert southwest; not much mud around here.  I'm just wondering if I've got a potential of having the same problem or do these bolts only sheer off when running hard through deep mud and such.  Did Joyner realize this problem and include 12.9 bolts in later versions, like my model year?  Seems like this problem appears in the earlier model years.


×
×
  • Create New...