Quantcast
Jump to content

blissman20

Commando 650 snorkel?

Recommended Posts

New to the forum and Joyners.  Rode plenty of other machines, even used to ride with Ostacruiser(yes I’m in some of his videos).  I have been doing some long over due repairs/modifications/maintenance to my commando.  I wired in a new voltage regulator, wired in a new ignition, moved and replaced the choke, wired in second battery(back up) on a switch),  slapped on some 30” mudlite XXL and a yutrax rear bench seat for the kids.  While doing all this I noticed the intake is rather low and the air cleaner inlet seems to be in a bad spot for sucking in dirt and dust.  

Has anyone ran a snorkel on these? I’m sure I can’t be the first to think of it.  I searched but didn’t find anything.  

 

Just a pic of my unit

BA7D9DAF-99F9-45DF-A9B7-7C7640536191.jpeg

Share this post


Link to post
Share on other sites


since it seems no one else has done it I might as well be the first lol.

i went and did some basic shopping today, need glue and two more pieces tomorrow. 

 

So far I’ve removed the old intake which was taped on and worn out.  Marked and used a holesaw to where it will come out.  The intake will be completely 1.5” abs, coming to a 3” adapter where the cone filter will be attached with a flow pot as a rain shield.  More pictures to come tomorrow 

33693843-424C-48F6-8657-BF1A2595F22B.jpeg

4C351C59-4475-4AB1-8880-6FB823D16EE2.jpeg

96A8076D-A6A5-4D0B-9493-0424E0103F95.jpeg

44A060DF-64C8-4944-B5DC-FBD5FD890E61.jpeg

Share this post


Link to post
Share on other sites

More progress today, cut and glued all pipes, and trimmed edge down on the flower pot and built the rain cover supports.  Just need to clean up the edges and paint it all

BE2BBE45-564C-44DB-AEC5-518D23E0C4F3.jpeg

617D7A12-0D56-454B-9A6B-839B3FDE990A.jpeg

821D5854-0EE2-4206-BBFB-C2C780F9351C.jpeg

0B36580A-6AF5-419F-BECF-61CA9DC005FD.jpeg

4F53C9DC-6871-4D3B-B0F1-863394BBD222.jpeg

3957B5B4-1DCA-450D-93C5-7B1246AB1A73.jpeg

A90417E6-A100-4692-98A2-D10BB9336798.jpeg

313DFF80-AAE6-46BA-AB00-AE8EA03DEBD1.jpeg

9A427BF4-F25A-4BEB-AFAC-D9BB1842D265.jpeg

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By bmoody4550
      I recently got a 2006 Joyner 650cc Commando. It was not running when i got it.
      I put a new fuel pump and alternator and is up and running.
      My problem is when I originally got it started it seemed I didn't have 1st gear.  I was able to get it moving from 2nd and was sure I got it into 3rd.
      In my process of diagnosing the first gear issue and I realize I have first gear because it is where I thought 3rd gear was. But now I don't seem to have 3rd or 4th gear.
      The shifter itself seems sloppy and needs a little rehab if that is possible. Replacement available?
      Cables are worn so I don't know if they have too much play to properly shift. Can't seem to find any cables available to replace. 
      Can someone tell me which cable should be first and second and 3rd and 4th? One is black and the other is red.
      Ultimately it may be a transmission problem internally.
      As long as I have 1st and 2nd the machine will work for me going through the woods picking up wood.
      Any help is greatly appreciated.
      New to this if you can't tell.
      Thanks
       
       
    • By WCF
      We would like to add a repair and parts shop to our shop in Southern  California for the Joyners. How many Joyner people in the area do we have that own Joyners? 
    • By Kinarfi
      Dealers - - - also see http://www.utvboard....dpost__p__16044 & http://www.utvboard....dpost__p__16045
      No Limits Powersports in Arlington Texas - Contact Jarrad (Snowman6479). (817)695-1151 http://www.joyner-atv-utv.com/
      Silver Bullet Motorsports in Yuma Arizona - Contact (silverbullet). (928) 344-2117 http://www.silverbul...otorsports.net/
      Thin Air Powersports in Spring Creek Nevada - Contacts Tim (Anylizer) or Amanda (Long Track Lady) (775)753-8223 http://www.thinairpowersports.com/
      McCoy Motorsports in Pikeville Kentucky - Contact Art (Art) (606)432-1556 http://www.tobefast....sa-c-63727.html
      Mudslingers Motorsports, Alberta, Canada, Trevor Carson (780) 576-2860 cell: (780) 984-2711 http://www.mudslinge...website_006.htm
      Joyner USA In Phoenix Arizona - Contact Brandon Deruiter Office (480) 882-9612  Email [email protected]   Web site Joyner-usa.com

      I also take suggestions for any and everyone!!
      parts & pieces from dealer in Germany
      http://www.utvboard.com/topic/3168-joyner-parts-and-all-chery-and-lj276-engine-parts/?p=18349
      AIR FILTER K&N RU-1000, RC-4160, and another link
      If you have the new 09 filter box, w/ Fram # CA-7764
      ALTERNATOR BELT 14mmx 755mm replacement that works....Carquest #K040292
      Alternator Belt - Checkers Auto Parts KO40292 - Exact Match
      Battery, according to 2 scoops, Duralast 51-DL is the correct size.
      OIL FILTERS
      Troopers with Thread Size 20X1.5 MM can use:
      WIX 51347, 51334 --- Napa 1347, 1334, PS1334 --- Fram PH6010A, PH3593A
      Troopers with Thread Size 3/4X16 " can use:
      Fram PH4967, Napa 1394 & Wix 5194 (slightly longer than original, Wix 51396 (even longer yet).

      OIL COOLER See thread, http://www.utvboard....768-oil-cooler/

      Oil Pressure Gauge Replacement
      Zorro found some at his Local Marine Supply store
      Sending Unit -- TeleFlex Morse Part # IA15001 0-80 psi, 240-33 ohm
      Gauge -- TeleFlex Morse Part # 57903P 0-80 psi, 240-33 ohm
      Manufactured by Veethree Elec. & Marine LLC
      together cost aprox $80.00
      Says it fits the existing hole perfectly Thanks Zorro
      Plumber added this reference; http://www.spydertal...pressure-gauge/ which Crosses over to a Sierra part# 01858990
      IMHO--I would move the the sender away from the exhaust manifold.

      FUEL FILTER replacement, Fram Fuel Filter G4777

      FUEL PUMP replacement, Bosch 0 580 254 910 According to Brostar, (Thank You!!)
      http://www.ebay.com/itm/Hayg-OEM-Inline-Fuel-Pump-0-580-254-910-0580254910-New-/230568738342#vi-content (updated 05-2015)

      PRE FILTER KNN-RC-4160-DK prefilter
      HEAD LIGHT REPLACEMENT Sylvania H5006 replaces the whole bulb, It works sooooo much better than the original.
      SPARK PLUGS NGK Iridium BKR5EIX-11, NGK 2387, NGK BKR7ES-11, Bosh 3311, Denso Iridium plug 5310 IK22

      CV Boot Kit There appears to be a difference between inner and outer boots, I used a NAPA CVB6862340 for my outer rear, fit good but not tightly on the CV end, I held it on with Tyraps
      Autozone part # 03606. Comes with bands and grease for $11.99, quick/split boot. K2181 95 Geo Metro $15.99
      NAPA #686-2149 fits for the Troopers inner CV. It's a speck tight but only about 1/16".(Lenny)
      Napa 686-2181 CV Boot from a 95 Geo Metro.
      http://www.norrecind...tart=1&cat=1394 or
      Norrec Industries then Application, then UTV, then look up joyner, they have them all
      Polaris CV Boot Kit # 2203438, (PR-8061)
      Also see CV boot for driveline? - UTV BOARD - Side X Side and UTV Forum

      Valves shims are 25mm, Joyner shims start at 2.18 and increase in increments of .02 up to 2.80, The Honda shims come out of CB450s and GL1100s, start at 2.30 and increase in increments of .05
      http://www.mawonline...gle/P137630.HTM
      http://stores.ebay.c...&_sid=120606839

      Master Electrical Switch Key
      http://www.jegs.com/...oductId=1231908
      http://www.pegasusau....asp?RecID=1467
      Make your own, it's easy, I did, just in case mine breaks.

      At the suggestion of one of our members, here's some info on the gas gauge sending unit.
      3 ohms is full, 13 ohms is 3/4, 23 ohms is 1/2, 63 ohm is 1/2, 110 ohms is empty.
      Electrical readings are: F=0.75v-98ma, 3/4=1.91v-82ma, 1/2=2.7v-71ma, 1/4=3.3v-62ma, 0=4.1v-52ma, E=5.0v-39ma
      0 is top of red zone, E is bottom of red zone.


      Manuals and Information


      Trooper T2 weights, 380lb. on each front wheel, 480 lb. on left rear, 520 on right rear TOTAL = 1760 pounds

      down load this and save it!!!!
      Torque Values Select Your type of bolt at the top. http://www.engineers...bles/torque.htm
      My Snorkel Made from a Sears ShopVac 7' Hose and the Extension Wand,


      Oil Drain QuickOilDrainValve.com
      http://www.oildrainvalve.net/ez-oil-drain-valve-ez-103-12mm-1-25/
      the best way to change oil, IMHO Kinarfi
      Fram Sure Drain #SD3

      Paint as recommended by Brostar: http://www.zynolyte..../rustmaster.asp

      Supplier of parts in General

      http://www.cxracing.com/default.aspx
      http://www.jegs.com/
      http://www.summitracing.com/
      Pegasus Auto Racing Supplies - Home Page
      TireRack.com
      McMaster-Carr
      Discount Hydraulic Hose.com

      Tie Rod Dust Boot, Checker Auto#13566

      Rod End / Heim Joint Seals , http://pitstopusa.co...-end-seals.html, thanks rocmoc
      Ball Joint Rod Ends AKA Heim Joints
      16 x2.0mm threat, 16mm ID, 21 mm thick,
      I got mine at McMaster-Carr 4483T36
      PTFE/Kevlar Insert, M16 x 2.0 x 40.mm shank, 21,966 lb static radial load capacity, 23°, $25.60 ea. or $204.80 for 8
      http://www.vxb.com/page/bearings/PROD/Kit12360
      http://www.vxb.com/page/bearings/PROD/Kit12960

      14 Inch Tires That fit our Stock Wheels Note that the stock lug bolt pattern is 4 X 115
      STEEL WHEELS http://www.utvboard....dpost__p__10804
      JC Whitney for all Auto parts - Car, Truck, Jeep, Motorcycle & RV Parts
      Interco Tires SSR-24R - INTERCO SSR Series Tire - Quadratec
      Interco Tires SAM-12 - INTERCO Super Swamper TSL Tire - Quadratec
      TSL Radial | Interco Tire
      Maxxis Bighorn 2.0 AT26 X 11R 14
      General Grabber AT2 27x8.50 R14 95Q 6PR OWL $90.10 http://ssl.delti.com.../GRABBERAT2.jpg
      National Chaparral A/P 27x8.50 R14 95Q 6PR OWL $113.80 http://ssl.delti.com...ChaparralAP.jpg
      Kumho Road Venture MT-834 27x8.50 R14 95Q 6PR OWL $110.30
      Mastercraft COURSER A/T 27x8.50 R14 95Q 6PR OWL $87.00 http://ssl.delti.com...t/COURSERAT.jpg
      Cooper Discoverer LT 27x8.50 R14 95Q 6PR OWL $99.60 http://ssl.delti.com...iscovererlt.jpg
      Laramie Performer RV 27x8.50 R14 95Q 6PR OWL $100.70 http://ssl.delti.com...PerformerRV.jpg
      ITP MUD LITE XTR 27-9-14 $87.99
      ITP TERRACROSS R/T 26-9-14 $144.99

      15 inch Wheels [Be sure to get the correct lug nuts, 12X1.5
      Vision Wheel Inc Vision Wheel
      ITP has one now also, getting info. ITP TIRES - The World's #1 ATV Aftermarket Tire & Wheel Source :: Holeshot

      Non Trooper Info
      u joints for joyner renegade are Spicer 5-1501X and Precision 391. They are American work great. graybeard9
      Differential Bolts
      40 28 to Full 25 96144A227• 8.33
      1100 Trooper T2 ECU Wiring Diagram.pdf

       
      Joyner Trooper Differential Rebuild Kit .doc
    • By blissman20
      Hey guys, just to give you a bit of back story here first.  I used to ride big mud machines and SxS in the swamp.  Went through a divorce and lost almost everything.  What I got to keep was a snowmobile that I had for years and never rode anymore and wasn’t worth much to me so I decided to try trading it for more or less any UTV/SxS I could.  Well that landed me here, I just traded it for a 2008 Kandi KD650 which is a direct clone of the Joyner Commando 650.  The machine is in rough shape but runs and drives.  I have a few things to repair on it. (Seized choke cable, seized Ignition, and needs a voltage regulator). Going to to princess auto today to pick up a choke cable, and ignition, I have a voltage regulator from an old project that I will wire in.  
      The only thing I am wondering about is the rear end.  The guy I traded it for told me only one rear tire will spin when in 2 wd.  Is that the way all of these are is do  I need to rip it apart.  Also is there any aftermarket support for rear axles or axles that will fit that can be cut down and sleeved and rewelded.  Buddy there did some rednecking with a Polaris axle but not sure how strong it is. 




    • By silverbullet
      Hello
      I have just recived date of first delivery of 650 differentail.We have taken these rear differentails apart and re shim them and installed new upgraded hardware.They will be shipped out starting 7/25/15.
      Thanks Silverbullet


×
×
  • Create New...