Quantcast
Jump to content

Massimo Tboss 410 feels like the brakes are stuck when taking off


Steven78
 Share

Recommended Posts

Hi I have a t boss 410 is about a year old with 150 MI and it feels like the brakes are stuck when you take off but in neutral it rolls perfectly I also have a t boss 550 that does not do this so was just wondering if anyone else has had this issue or if it is common with this machine also on the 410 have had the stator motor and voltage regulator replace once already and think it is bad again not sure if this would have anything to do with the other issue any help or advice would be greatly appreciated thanks in advance

Link to comment
Share on other sites

  • Alex changed the title to Massimo Tboss 410 feels like the brakes are stuck when taking off
16 hours ago, Steven78 said:

 

Sorry to be asking so many questions but information is so hard to find on these have you had any problems with yours this one only has a hundred fifty miles on it and they have been very gentle miles all in town on flat ground. The stator was also bad when the voltage regulator was changed and already doing the same thing again 

Link to comment
Share on other sites

Fortunately I have not had any issues, except for a faulty starter solenoid. It took a while to track that down, but once I replaced that, it's been fine. I don't have many miles on it, though. Do you have a manual for it? There's a free download of a manual here on this site if you need it. 

If yours is the same as mine, you have the digital display. If you toggle through the options using the button on the right side of the display, you can see what the voltage output is while it's running. Mine has never been higher than 15V, and that's usually right after I start it. After that it's in the 14's. Obviously something is wrong somewhere if it keeps burning up voltage regulators. I would check any grounds I could find, and clean them and coat them with some dielectric grease. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Topics

    • By Steven78
      Does anyone know if there is an after market voltage regulator for a 2020 Bennche Tboss 410? 
      Thanks in advance
    • By Bret4207
      2019 Coleman Outfitter 550, 160-ish hours. Was driving it slowly and it just slowed down and died. Won't start. Pops once as soon as I start cranking and that's it. I have great blue white spark on the spark tester, jumps 1/2". Changed injector, no joy. Changed plugs to new several times, no joy. Pulled injector power wire and tried ether through air intake after removing air filters- nothing! I do notice if I put my hand over the air intake where the filter goes, I get pressure  pushing back at me. Jumped time? Stuck valve? Is there a decompressor on this that could be malfunc?
       
      This is the one I've had that was inop for months and months while Coleman tried to find someone to fix it. Warranty is long expired now. I'll never have anything good to say about this thing.
    • By Mac1942
      Take protective plate off under the rear axle brake and loosen the large adjustment bolt until the parking brake is free, Then tighten the brake cable nuts on the left cable attached to the main brake pedal until the slack is out enough that stepping on the main brake releases the parking brake. Once released, the large adjustment bolt for the parking brake assembly can be adjusted to the desired tension to keep the UTV parked when the parking brake is applied. Then it is simply a matter of adjusting the parking brake cable to allow the main brake to release the parking brake. Replace the steel protective plate under the rear axle and your are done.
    • By Farm Boy
      It has done this since day one that we purchased it from Tractor Supply. I contacted the service man that Tractor Supply recommended and he told us that there wasn't anything he do to help us with. Has anyone had this same problem and can offer suggestion on to correct this issue ? It would be greatly appreciated.
       
    • eManualOnline
    • By Viper0012
      Hope I have this in the right area but i am having an issue with the drive by wire system on my Joyner sandviper  with the 2.0. I have done all electrical checks to pedal and the electronic throttle body. But have no actuation of the throttle, meaning the engine starts and idles but no vroom vroom. Wondering if anyone has come across this issue I am leaning towards ecm but due to the rareity of parts hoping not.
  • Similar Tagged Content


×
×
  • Create New...