Quantcast
Jump to content


Coleman 550 Outfitter – Easy Winch Remote Implementation

TexasBuckeye

By TexasBuckeye
in Coleman UTV SxS Forum

 Share

Recommended Posts

TexasBuckeye Newbie

TexasBuckeye

Posted
Posted

I ordered remote control hardware from Amazon https://www.amazon.com/dp/B07P2G4T22?psc=1&ref=ppx_yo2ov_dt_b_product_details and initially installed module behind the switch panel and wired it into the winch control switch.  After researching the 2014 HiSun service manual posted by another forum member, I discovered a better way to implement (fyi-this is not documented any Coleman service manual that I could find)  My UTV is a 2022 model, but the wiring appeared to be the same for my model. 

There was an unconnected Molex plug hanging under hood on the driver side (Molex#33471-3301), (see photo).  I purchased a Molex 3 wire connector ((Molex#216283-1032) directly from Molex  for $5.82 including tax & shipping.  This connector has the 3 wire pigtail to easily splice to the remote control module wiring.  https://www.molex.com/molex/products/part-detail/cable_assemblies/2162831032 .

I added a ground stud near the parking brake mechanism in order to connect the black wire from the module see photo) .  I added velcro to the module and then secured with zip ties to the back of the nameplate bracket (see photo). 

See the wiring diagram for hook-up that I used.  The loose blue wire is the antenna so it is not connected to anything.  

GroundStud.JPG

IMG_4159.JPG

IMG_4163.JPG

IMG_4164.JPG

IMG_4166.JPG

Molex Wiring.pdf

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • Hunterman22
      2021 Hisun 500 Axis. Reading Codes??
      By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
    • RBonds007
      2019 Cub Cadet Challenger 400, trailer to transport the Challenger, and new, never used winch for sale
      By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...