Quantcast
Jump to content

Hisun Sector E (2021) Fault code 54C 3

Billsectere

By Billsectere
in UTV General Discussion

 Share

Recommended Posts

Billsectere Rookie

Billsectere

Posted
Posted

Creeping down our steep driveway after a 3 mile hilly run. Using the engine to help break. I'm in 4WD and Low "gear" mode. Suddenly there is a "release" type pop and the engine is no longer breaking as sometimes happens over a certain speed. No problem I apply more breaks and come to a rest down the hill. BUT this time the "back up" alarm is beeping and now the engine is just dead. Error code was initially 54C 2 but after resting overnight it now says 54C 3. As soon as the key turns on I get the alarm and nothing from the motor. It does look like the flashing engine thing shows a square box in the middle front is flashing. I have tried to find those codes but no luck yet. I wouldnt know what to do with them anyway. Any insights appreciated.--Bill

 

  • Like 1
Link to comment
Share on other sites
  • 2 weeks later...
Hisun Sector E1 code 54C 3 Newbie

Hisun Sector E1 code 54C 3

Posted
Posted

Hello, I have the same issue. I tried testing all the batteries and all says 6.0 volts. That code 54C 3 comes on soon as I turn the key. The company I bought this thing from is out of business. I have had this issue for about 8 months. Know one works on electric golf carts and Hisun said it might be a main board. Lol. I will never by a Hisun or electric golf cart again!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Mark T
      Can I put a larger engine in my 400 colman UTV ?
      By Mark T
      MY 400 is gutless. I would like to know if I can upgrade to a larger engine ?
    • wnc woods
      Coleman ut400 add lower gear
      By wnc woods
      Is it possible to add a low gear to the Coleman ut400? If so please help. Ty
    • DLJ
      Hisun 800 shuts down
      By DLJ
      Have a Hisun 800 it runs for about 35 minutes then stalls. Crank's over but has no spark. Let it sit for 15 to 20 minutes and it starts and runs again for about 35 minutes. Changed the CDI / ECU controller and still does it.
    • Jeff j j
      2023 trailboss 750 low rpm and mid rpm miss
      By Jeff j j
      I have a 2023 trailboss 750. It has a low rpm and mid rpm miss that won't go away. Took it to a shop and had full service, valves adjusted and a sensor replaced. Think the miss is worse than before. Any ideas?0
    • Xov
      New AMP Pro Owner
      By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...