Quantcast
Jump to content


Winch Problem

JFC

By JFC
in UTV General Discussion

 Share

Recommended Posts

JFC Newbie

JFC

Posted
Posted

I have a  3500LB Winch that only runs in one direction.  Inward but not Out.  Replaced the solenoid module.  Makes "click" when I push the "Out" button and the motor tries to spool out but then stops and begins to "click".   Does anyone have suggestions what I should try next?       

  • Like 1
JFC Newbie

JFC

Posted
  • Author
Posted

2 switches installed.  The remote (tethered) and the dashboard toggle switches react both the same way.  Push "Out" and the motor attempts to start but stops and then it "clicks" .  

  • Like 1
TxDoc Apprentice

TxDoc

Posted
Posted

Go back and check your solenoid connections. With DC applications, motors, trailer lights, etc., a bad ground is very often the source of a malfunction and that can be a corroded connection.

Are you sure your battery is okay? Low voltage will cause a motor to activate and stop.


Take multimeter and go one step at a time to confirm, grounds, current flow and voltages when activated.

If both switches test to be good and the motor can be jumped to start, bypassing the switches... You need to go back to the solenoid. Even though NIB, it may still be bad.





Sent from my motorola edge plus 2023 using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • Sammy
      2017 TW450 Kohler ECH440 runs out of fuel when running wide open.
      By Sammy
      Runs fine just putting around the yard. Get it out on the road and about a half miles it runs out of gas. Let it idle for a few minutes and it will run for another half mile and do it again. Replaced both fuel pumps and filter. Does anyone know if I can get rid of the factory fuel pump?
    • dilger
      Transmission vent leaks oil out
      By dilger
      Transmission vent leaks oil out of it after using 
    • mike28honda
      Axis 500 cuts out at about half throttle
      By mike28honda
      I have an Axis 500 and never had any problems until now,it cuts out 
      at around half throttle. I changed the TPS with no difference, acts like the seatbelts aren't set but can get up to around 15 mph as long as I don't give it too much gas, thanks for any advice 
    • Firewalker918
      Anyone customized their uv34XL? Also, looking for seatcovers
      By Firewalker918
      I have a 2021 UV34XL and I am kind of looking to change it up from the orange wheels and maybe do a wrap?  Please share photos of any XLs that has been modified to look better and any seat covers recommended.thanks
       
    • Hoppy one
      Bennche 500, replaced stator no fire
      By Hoppy one
      I replaced the stator on our Bennche 500 because it was not charging. It ran as long as you kept the battery charged. I replaced the stator now it’s not firing. The only problem I found was a wire in the new stator for the crank position sensor was in the wrong place in the plug. I switched it around but still no fire. Putting a meter on those wires and cranking the motor showed no voltage from the crank position sensor. Something I did or a bad “new “ part? Thanks for any ideas.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...