Quantcast
Jump to content


2019 Coleman 550 outfitter coolant in oil. (milky oil)

amiracle40995

By amiracle40995
in Coleman UTV SxS Forum

 Share

Recommended Posts

amiracle40995 Rookie

amiracle40995

Posted
Posted

I've never seen the temperature go high on this thing. the fan runs almost all the time even though the sensor is  reading at the very bottom of it's range. ive taken the cylinder head off.  (nothing definitive but maybe a little fuel on top of piston with oil in it.i don't think this has anything to do with my problem )head gasket is 3 layers deep and I noticed some grit that might have been in between layers but nothing to say the head gasket wasn't intact.  black carbon build up on piston. I've looked all over the head for cracks from over heating. I'm about to look again for hairline cracks that are extremely difficult to see. my buddy helping me said to order rings in case they are letting oil pass thru he also said get a new head gasket.. I'm looking at water in oil first and I'm not ordering rings. I haven't checked the oil cooler to see if it's defective yet.  I'm just hoping someone had a similar problem. my only problem so far has been having to change the spark plug every 100 miles with 93 octane run thru it. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • monkthumper
      2020 Hisun Sector 750 no pwr to fuel pump
      By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • Ed Michael
      Older Landmaster LM 650 Fuel Problem
      By Ed Michael
      My older LM 650 is blowing fuel into the air cleaner.  Any idea on what would cause this?  It is the Suzuki motor.  Not sure what model year it is.
      Thanks
      Subaru SxS.mp4
    • ToughLuck
      2021 Massimo MXU 1000 Runs Rich
      By ToughLuck
      I have a 2021 Massimo MXU 1000.  Last winter the front drive shaft sheared off inside the motor and it was cheaper to buy a new motor than to take it apart in order to remove the front drive shaft that was broken inside the case…
      Now it is running rich, seems to maybe be geared too high, does not accelerate well once you hit about 28mph.  I’ve replaced the O2 sensor.  MAF is next (I accidentally ordered the wrong one, but when I removed the old one you can clearly smell fuel).  
       I’m not a motorhead but I can turn a wrench.  Any ideas how to get this motor optimized?  The motor has about 300 miles on it.  I broke it in as recommended in the manual. 
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Homeowner A
      Black O2 Sensor?
      By Homeowner A
      I've been having misfire issues with my UTV 400 when it gets warm and I've thrown all kinds of parts at it so far with no permanent resolution.  Today I removed the O2 sensor and it is black on the end.  To me that means it's running rich and/or the sensor isn't working.  I replaced the sensor with a new one and will see how it goes I guess.  With EFI, I'm wondering why the sensor would be this way with low hours and mileage?  Is there a way to adjust or lean out fueling on these?  Thanks in advance.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...