San Felipe Poker Run
-
Similar Topics
-
By CYJSP2009
Hello Everyone
Brand new Joyner CV AXLES are waiting to be unloaded at LA port and then be sent to warehouses in Charleston, TN , BALTIMORE, MD and Groveport, OH. Estimate they will be available for shipments to end customers in about 2-3 weeks.
These CV AXLES are ordered in February this year and now it is middle July. Very long time to get these parts. Qty for each model is not big. Detail as below:
S/N Part No. Description Charleston, TN BALTIMORE, MD Groveport, OH Total
1 D650.03.02.02.00 650 Sand Spider Rear left 3 2 3 8
2 S650.03.02.02.00 650 Commando Rear 7 6 10 23
3 TR1100.03.01.03.00 TR1100 Front 3 3 4 10
4 D650.03.02.03.00 650 Sand Spider Rear Right 3 2 4 9
5 S800.03.02.02.00-R2 800 R2/4 Rear Shaft 4 4 6 14
6 TR1100.03.02.03.00 TR1100 Rear 6 5 9 20
7 S650.03.01.02.00 650 Commando Front Left 3 3 4 10
8 S650.03.01.03.00 650 Commando Front Right 3 3 4 10
Below items are also available. These items can be shipped in days
CAGE:
1. 800 Renegade R2/R4 Front outer cage --- 5 pieces
2. 800 Viper SV1100 Drive shaft rear Left outer cage --- 5 pieces
3. 800 Viper SV1100 Drive shaft rear left inner cage --- 3 pieces
CV BOOT:
1. 650 Commando Left Front / 650 Commando Right Front /650 Sand Spider Rear Left / 650 Sand Spider Rear right / OUT CAGE 2 pieces
2. 650 Commando Rear OUT CAGE 1 pieces
3 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE 2 pieces
4 650 Commando Left Front / 650 Commando Right Front INNER CAGE 1 pieces
5 650 Sand Spider Rear Left / 650 Sand Spider Rear right INNER CAGE 1 pieces
6 650 Commando Rear INNER CAGE 1 pieces
7 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE INNER CAGE 2 pieces
Anyone who need above items please contact me at [email protected]. Thanks.
Other Joyner items needed, you can also contact me and I will try to help.
Have good day
Casey / Leaf Asia
2021-07-20
-
By Pablo
Hi. Ive been searching for a wiring diagram, hopefully with photos, part #s so I can try to repair damage from rats eating wiring over the winter on the M550 cub cadet UTV. (sigh). haven't had any luck. i have a plug with dangling wires from under seat, next to battery compartment and hope to take to dealers to see if he can order replacement and hopefully it comes with long enough wires that i can splice back into remaining wires. not going to be easy. I'm not sure if there is any more damage, but would have to disassemble to get to bare chassis. sigh. not sure I can do all that, but just trying to find a diagram with photos. no luck. any ideas. thank you.
-
By Hisun .500
So my hisun 500 is tore up and all the wiring is wasted i was wondering can i pull out all the wiring and just put in the. Basics .please help
-
By Kevin M
Hello all. I am new to this forum and new to SxS in general. I recently purchased an 16 Odes Dom 800 with the issue of a prominent knocking noise at idle and it’s very jerky in forward and reverse gears. It does not sound like an engine knock. I bought it cheap knowing about this problem with hopes of it being a cheap and fairly easy fix that I can do myself. Would a bad belt be the cause this symptom? I’m looking for a starting point to begin diagnosing and fixing the problem. I recorded a video of it but am not sure if I can post it on the forum. Any help is greatly appreciated.
-
By robwork9
Hopefully someone out there is a T-Boss 410 electrics expert or a Massimo mechanic is viewing this. I parked my 410 and it was working great. I came back a week later and attempted to crank it and nothing. Turned the key and no power. Figured it was a bad/low battery so I charged it. Still nothing. Attempted to jump start it and still nothing. Usually when I put the key in and turn it to the first position, the display comes on and I hear the ECU and other items boot. Now it is doing nothing.
I slowly went through the electrical system and found the main fuse attached to the starter relay, part 71602 (pic 1) blown. I figured replacing this fuse would fix my problem. It didn't. I then ordered a new starter relay thinking maybe that part had gone bad and caused the fuse to blow, but a new relay did not fix the problem.
I have found a work around for starting the machine. If I take one of the purple/black leads (pic 2) and insert one of them in the bottom right of the starter relay (pic 1 and 3) then the machine will get power even with the key in the off position. I'm bypassing something but don't know what. I can use my right hand to hold the wire against the lower right of the starter relay, reach over and hold the brake with my foot, then take my left hand and turn the key and it will crank. As soon as I remove the wire from the relay the machine shuts down. I have even removed the power distributor box and it will still get power when I touch the wire to the relay. Of course this is not the way it should work but if I can't solve this problem somehow I may just have to rig a connector to the relay and bypass whatever is causing the electrical issue. Massimo has told me the purple/black wires on my model are not used.
Any help in figuring what my problem may be or other items I can try?
v/r,
Rw
-
-
-
Gallery Images
-
By HiSUN PROBLEMS,
-
By islander83,
-
By Hammerdn,
-
By ricksrb,
-
By Travis,
-
By stevozz,
-
By TomWA,
-
By plumber,
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.