I have a Rural King version of the Hisun Sector 250 with about 75 miles and 15 hours on it. It just started being difficult to start and idle. But if I hold in on the gas a little it will start and run until I left off. It also runs good and will run good until I stop then it idles for a few seconds then quits. Its about 4 months out of warranty. Battery voltage is fine before, during, and after starting. Oil is clean and clear. Gas is fresh. I can hear the fuel pump spool up when I turn the key to actually start it, not when I turn it to the on position though like on most other UTV's I have owned. Its really odd and has me perplexed. The only other thing that I have noticed is that the engine temp indicator on the left side of the dash only indicates one bar regardless of how warm the engine is. Other than that, it runs great. Just hard to start and won't idle. Any suggestions? It has me perplexed.
I recently got a 2006 Joyner 650cc Commando. It was not running when i got it.
I put a new fuel pump and alternator and is up and running.
My problem is when I originally got it started it seemed I didn't have 1st gear. I was able to get it moving from 2nd and was sure I got it into 3rd.
In my process of diagnosing the first gear issue and I realize I have first gear because it is where I thought 3rd gear was. But now I don't seem to have 3rd or 4th gear.
The shifter itself seems sloppy and needs a little rehab if that is possible. Replacement available?
Cables are worn so I don't know if they have too much play to properly shift. Can't seem to find any cables available to replace.
Can someone tell me which cable should be first and second and 3rd and 4th? One is black and the other is red.
Ultimately it may be a transmission problem internally.
As long as I have 1st and 2nd the machine will work for me going through the woods picking up wood.
Any help is greatly appreciated.
New to this if you can't tell.
Just purchased a 2018 Hisun Sector 250. The gear shift is hard to engage. Tried depressing the brake pedal, no change. Tried with the engine running and turned off, no change. The gear shift cable, from the dash to the trans seems to be grinding. With my hand on the cable I can feel it grinding, vibrating, as the gear shift is moved up or down. Can this cable be removed and greased or does it just need to be replaced?
By Gary T
I generally use my challenger for light duty misc. use, and for plowing. The one thing I dislike about this machine is the difficulty in shifting. I've had it the shop and they adjusted the shifting lever, but I still have issues. Some times it shifts ok, but the problem is it is hard to get it to move the lever from high to reverse or low to high or from any gear to the other. Seems I always have to accelerate a little to get it to engage to what gear I need it to go to. This is definitely not normal.
By Wild child 911
I have a 2018 model Hisun 450 EFI UTV. I have done over 6000 trouble free kilometers. About 4 weeks ago i felt that utv was not performing like it should. Done a compression test and found to be low. Replaced rings as they were worn. I drive in a very dusty environment. The problem of low power is still there. I have checked cam timing, valve clearances, compression up to 9.5 bar, done leak down test and valves are seating, stripped and cleaned fuel pump, removed and cleaned throttle body, checked for leaks on throttle body manifold, replaced spark plug, tested stator coil, tested hv coil, checked all electrical connections, checked injector. UTV starts easily and idles for 5 seconds and cuts out. When utv starts, it will rev up the first time and then start to miss as if it goes into a limp mode. If i lift my foot of the accelerator utv will idle for 2 seconds and then die. It starts immediately again. Would the air flow/ air pressure sensor or exhaust gas(lambda) sensor cause this. I cannot test them as dont know the correct values. Any suggestions will be highly appreciated.