U force 800 steering

a4x4nutt · 2026-04-28T18:38:37+0000

2021 uforce 800 turning radius is awful . I just bought it added perfex lift And 1.5 wheel spacers The turning radius was bad before the lift . I looked for steering stops under the tie rod boots and steering knuckle for steering stops . Found nothing . Are the stops inside the steering rack ? Is there a replaced steering rack with longer throw to curb this issue ? Any suggestions?

By a4x4nutt
April 28 in CFMOTO UTV SxS Forum

https://www.utvboard.com/topic/59929-u-force-800-steering/

Followers 0

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Reply to this topic...

× Pasted as rich text. Paste as plain text instead

Only 75 emoji are allowed.

× Your link has been automatically embedded. Display as a link instead

× Your previous content has been restored. Clear editor

× You cannot paste images directly. Upload or insert images from URL.

Insert image from URL

https://www.utvboard.com/topic/59929-u-force-800-steering/

Followers 0

Go to topic listing

Popular Now
- 5
  
  Hoping someone out there somewhere can help.....2019 Massimo Buck 400S
  
  By AaronD1982
  Started Thursday at 02:09 AM
Similar Topics
- 2021 Axis(Hisun) 700 Will not fire up
  By Burk
  
  I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
- Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
  By rdc
  
  I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC
- Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
  By rdc
  
  Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
- 2021 Coleman ut400 rev limiter
  By Dave Jones
  
  So with seat belt on I can only get up to 20mph then it starts bucking until I get under 20 again. Diconnected the seatbelt and same thing. Reconnected seatbelt and unplugged speed sensor. Zoom..it flies. But now I have no speedometer. I have a new speedometer sensor on the way..any other ideas?
- 2021 Hisun 500 Axis. Reading Codes??
  By Hunterman22
  
  Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis. I have a 6 pin to a 18 pin adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???

Sign In

U force 800 steering

Recommended Posts

a4x4nutt

Join the conversation

Popular Now

Similar Topics

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

Activity

Browse