Quantcast
Jump to content

Help with 2006 Land Pride Treker 4410

Charles Cox

By Charles Cox
in Other UTV SxS Forum

 Share

Recommended Posts

Charles Cox Newbie

Charles Cox

Posted
Posted

Hello all, I'm new here. I found this forum by accident while trying to do some online research. I picked up a 2006 Land Pride Treker 4410 at a farm auction. It's a one owner UTV in pretty good shape. It runs and drives fine except it will not start out moving forward in 2WD. I have to start it moving in 4WD and once it's moving forward, I can switch it down to 2WD. If I try to start out in 2WD the engine revs but the unit will not move. Does anyone know what could be causing it? I'm thinking maybe a differential actuator? I know less than nothing about these units. The only thing I've been told so far is parts may be hard to come by. Any help would be greatly appreciated. Thanks in advance.

Link to comment
Share on other sites
  • 6 months later...
Podunktoo Newbie

Podunktoo

Posted
Posted

Hi Charles,

I'm new here too.  We picked up a used 2006 like you and recently had problems with engine revving ok, but no vehicle movement.  After finally getting the cover loosened so I could see belt between drive pulley and driven pulley, I finally found that the bolt and keystock had come out of the driven pulley.  I had to remove the tire on that side in order to see into the hole to find that parts had shifted and keyway was no longer lined up to allow keystock to be put back in.  I haven't been able to get it back into alignment and none of the manuals I have found mention anything about it.   We have no Land Pride dealers around so I'm at a loss as to how to get it fixed.

I'm not impressed with the manufacturing design of this vehicle. The pulley cover can't be removed completely because of insufficient clearance. A sheet metal panel must be removed to get the pulley cover off.  Nuts should have been welded in place at mfg. Screws holding the sheet metal panel in place are located behind 1" wire bundles that do not allow box end wrench or sockets to get onto the nut and insufficient clearance to allow a ratchet to move.  I'm sure that helped keep their maintenance shop funded by additional labor hours required for repairs.

Any suggestions for repair would be much appreciated.

Thanks,

Tom

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • hdtran
      Hello from New Mexico!
      By hdtran
      Hy (pronounce he), just bought a Hisun Sector E1.
      I'll be using it to haul logs and stuff in the Sangre de Cristo mountains.
    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • Chucky 1
      DO NOT BUY A LANDMASTER UTV!!!!!!
      By Chucky 1
      I purchased a new 2023 Landmaster UTV L4 in October of 2023.  UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better.  After about a week the unit started bogging down backfiring and stopping.  Gas fumes really bad, wait a few minutes and it would start up again.  Brought it back to the dealer and after keeping it for a few weeks said he couldn't find anything wrong with it.  Got it back home and it started acting up again, brought it back to dealer a week later and he said he found couple things that might cause it to do run bad and he was able to replicate the issue but didn't really know what was wrong.  Got it back home again after being at dealer for several weeks and the unit started running bad again right away.  Brought it back to dealer and he went back and forth with Kohler about possible fixes but just checked somethings and try to swap a few parts but still runs bad.  I called Landmaster HQ to speak with someone about a refund and was told that was handled at the dealer level.  Dealer called Landmaster and they told him they didn't do refunds or exchanges especially with units that had problems.  The dealer is now trying to get a new engine to but I have not heard anything as of yet.  I did file complaint with Better Business Bureau and they accepted my claim and reached out to Landmaster.  The National Service Manager called me and said the he had been contacted by the BBB about the complaint and he would look into it.  I told him that I would just like to have my down payment of $2,000.00 returned and never mind the over $1,000.00 I have paid in notes for a UTV that I cannot even ride on without hoping it gets me around the neighborhood.  I have found out that the 2024 Landmaster UTVs will have Vanguard engines due to issues with the Kohler engines.  Very disappointed in what is "Proudly Made in the USA" and the way Landmaster has treated this disabled veteran! 
    • Rufus Fruge
      Hello, I’m Rufus from the Bayou state!
      By Rufus Fruge
      Just wanted to check in and say hi to fellow members. I bought a 2023 T-Boss 550 last month just in time for hunting season. So far all is well. I went over it to check things out and learned a lot in the process.LOL! I certainly would recommend that all new purchasers should make it a point to do this because I can promise you that you won’t regret it.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...