Quantcast
Jump to content


2008 Joyner Trooper 2 4x4

InmortalJoyner666

By InmortalJoyner666
in Joyner UTV SxS Forum

 Share

Recommended Posts

InmortalJoyner666 Newbie

InmortalJoyner666

Posted
Posted

Hello everyone I am new to the page and I recently bought a Joyner T2 1100 cc, the wiring harness completely was torn apart. I bought the new harness and I'm having problems trying to figure out how to connect everything. I already connected the engine harness, and I ran the front harness through but there's extra plugs there that I don't see a connection for does anybody have the three harness part diagram for front harness, engine harness, and chassis harness and another question the harness that I took off that was bad did not have a fuse box in the front only one that was aftermarket in the back but the new one I have has one in the front and in the back. From what I'm told it's supposed to have two of them.

Jhen Explorer

Jhen

Posted
Posted

There will be plugs for the front and rear winch.  The wiring harness will also have extra wiring for add on lights etc.  Get it running, get your gauges, lights, turn signals and other accesories working. Then see what you have left.  There is a small wiring manual in the T2 manual on this (atv forum) web site under downloads.

  • Thanks 1
InmortalJoyner666 Newbie

InmortalJoyner666

Posted
  • Author
Posted
20 hours ago, Jhen said:

There will be plugs for the front and rear winch.  The wiring harness will also have extra wiring for add on lights etc.  Get it running, get your gauges, lights, turn signals and other accesories working. Then see what you have left.  There is a small wiring manual in the T2 manual on this (atv forum) web site under downloads.

Do you happen to have a picture of which ones are the plugs for the winch and which ones also are for accessories because there was such a mess of wires here extra wires that are not even part of the harness and it's such a mess I really appreciate your help and input

  • 2 weeks later...
natan Newbie

natan

Posted
Posted

ware did you buy the harness?

i looking to buy harness and I don't find 

Its  for my  2009 trooper 1100cc if someone else can help me to buy one it will be bless 

I have the buggy alrday 3 yers and still not use it at all 

  • 2 months later...
JOYNERPARTSGUY Rookie

JOYNERPARTSGUY

Posted
Posted
On 9/13/2022 at 7:44 PM, natan said:

ware did you buy the harness?

i looking to buy harness and I don't find 

Its  for my  2009 trooper 1100cc if someone else can help me to buy one it will be bless 

I have the buggy alrday 3 yers and still not use it at all 

I have one if you're still looking

  • 10 months later...
Guy Newbie

Guy

Posted
Posted
On 11/30/2022 at 10:35 AM, JOYNERPARTSGUY said:

I have one if you're still looking

I'll take it if he doesn't want it , if you want to email me with a price 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Xov
      New AMP Pro Owner
      By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Flanman55
      Wiring issues
      By Flanman55
      I have purchased a used Supermach700 (2008), It runs great after a new choke cable but. The temp sensor on the thermostat house is unhooked and can not find where it plugs back in. The fan has been un hooked from the sensor in the rad and cant figure out how it goes back together properly.  The fan was wired to a by pass switch and i just always leave it on but would like to work it properly. I assume the sensor went bad and not changed.
       
      any help would be great.
       
      thanks
    • Gerald Dillman
      2008 Joyner trooper transmission parts
      By Gerald Dillman
      Looking for a output shaft for a Joyner trooper t2. Went to move the buggy after sitting all winter and it appears the out put shaft that drives the rear wheels broke off inside the transmission so looking for the shaft or a complete transmission if someone has one
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...