Quantcast
Jump to content


Massimo Buck 250 won't start - engine light on

BeachBuggy

By BeachBuggy
in Massimo UTV SxS Forum

 Share

Recommended Posts

BeachBuggy Newbie

BeachBuggy

Posted
Posted

Massimo Buck 250 less than a year old.  900 miles on it.  Live on beach in TX...i.e. corrosive salt air and normally mild temps.

The story - one day, it randomly quit on idle and was tough to restart.  Next day, it occasionally cut out for 1-2 seconds while driving, then catch back to normal throttle.  Pumped gas pedal, not sure if that helped it catch.  Added some marine sta-bil and filled tank.  Ran well after that for a day.  Following day, wouldn't start.  Turns over, cranks, but won't start.  When it quit on idle that was the first time driven since we did have a freeze of ~25 degrees.

Full charge on battery. No spark.  Changed plug and still no spark.  Fuses look good, but fuse connection box has some loose clasps and spade were corroded. I bent clasps best I could and used dielectric on spades re-inserted.  Cleaned and checked every connection I could find.  Don't have a card reader to hook up, but did swapped ECU just to check that, and no change...after swapping ECU the engine light now stays on.  Previously blinked and then goes away.

Under warranty but service place is 2 hrs away. 

thanks!

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • barticus73
      Massimo T-Boss 560 or CFMoto Uforce 600
      By barticus73
      I am looking to buy a small UTV to do work around my property and priced a brand new Massimo T-Boss 560 through Lowes @ $10,500 out the door or a  Dealer provided CFMOTO Uforce 600 at $11,500 out the door.    Are there any glaring reasons to go with the Uforce 600 at an extra $1000?  Is one model more reliable than the other?  Any input greatly appreciated.
       
      Thank you,
       
      Jerry
    • barticus73
      Massimo T-Boss 560 vs CFMoto UForce 600
      By barticus73
      I am looking to buy a small UTV to do work around my property and priced a brand new Massimo T-Boss 560 through Lowes @ $10,500 out the door or a Dealer sold CFMOTO Uforce 600 at $11,500 out the door.    Are there any glaring reasons to go with the Uforce 600 at an extra $1000?  Is one model more reliable than the other?  Any input greatly appreciated.
       
      Thank you,
       
      Jerry
    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Chile
      Massimo MSU 700 Piston Clearance
      By Chile
      2018 Massimo MSU 700 EFI. I realize that this engine is essential the same as in all of the HISUN based Yamaha clones out there. I am in the process of performing a top end diagnosis/rebuild. I have an AMAZON top end rebuild kit on order in anticipation of this activity. 
      Question 1:  When exploring the myriad of top end rebuild kits on the market for these units there are some cylinder assemblies that have "686 cm3" badging next to the cam cain tensioner boss. Others compatible with the unit do not have this badging. The existing cylinder assy does not have the 686 badging. I am assuming that this simply verifies that the cylinder assy is for a 686 cm3 engine which of course the stock 700 series HISUN engines are. Am I missing something here or is this just a manufacturer artifact? With or without the badging the application listings all indicate compatibility with the MSU 700 series engines.
      Question 2:  I have reviewed at minimum a dozen videos associated with this rebuild. To date I have not found one that deals with piston/cylinder clearance and/or ring gap verification. The advertised specifications for these various "top end rebuild kits" all indicate: Cylnider bore = 102mm and piston diameter=101.5mm. The math yields a .5mm (as in 1/2 mm) difference. That seems to be a very large piston/cylinder clearance.  I realize I am referencing advertised specs rather than emperically measured values but the numbers have gotten my attention.  I have referenced the FSM and found it to be somewhat confusing in this regard. Hopefully the experts on this forum can enlighten me as to where my observations are faulty here.
      Any and all assistance is greatly appreciated .
      Thank you all in advance,
      Chile
    • Sando
      Massimo Buck 450 will not start
      By Sando
      2023 Massimo Buck ran for minute then died. Key on all power to dashboard but do not hear full pump turn on like previously. Also no fire at plug. ECU?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...