Quantcast
Jump to content


Need help with EFI wiring on a 2020 axis/hisun 500 UTV from Lowe’s

Tim Barbero

By Tim Barbero
in Hisun UTV SxS Forum

 Share

Recommended Posts

Tim Barbero Newbie

Tim Barbero

Posted
Posted

I left my 2020 axis 500 UTV parked under the carport for about 6 months and when I went to start it recently a squirrel has built a nest under the throttle body and chewed through the efi harness.  I stripped all the wires back and reconnected them with waterproof butt connectors.  The problem I have is there is one blue wire with a red stripe coming from the main harness this wire has 5 volts dc showing on my multimeter but there are two blue wires with a red stripe coming from 2 different sensors on the throttle body.  I looked through all of the bits and pieces of wiring left behind and there’s no indication that the three wires of the same color were all tied together.  Any help with this issue would be greatly appreciated.

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • Fmaxiron
      Honda Pioneer 1000-6 back windshield or screen.
      By Fmaxiron
      I just purchased a 2023 Honda Pioneer a couple of weeks ago and had the hard roof and a front Honda Pioneer windshield installed at the shop before taking ownership. As things are drying up here in NC, the grass and dust are beginning to fly right through the back of the cab while driving. I was wondering if anyone has any good recommendations on rear windshields, dust panels, or mesh screens to help stop this?
      Thanks a lot!
    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...