FOR SALE 2007 Joyner 1100 Sand Viper
-
Popular Now
-
-
Similar Topics
-
By rdc
I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC
-
By rdc
Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
-
By Kierobi
Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it.
Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming.
Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light.
Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
Thanks in advance and hope this all make sense!
-
By 180gtr
Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
SOLD ITEMS, I do not have these items.
Wheels
Tires
Engine
Transmission
Axles
Shocks
Control Arms
Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
Throttle Body $90
Starter $150
Alternator $150
Fuel rail, injectors, fpr $100
fuel pump $70
Map Sensor $50
Full set of Guages $150
Exhaust w cat, O2 SOLD
Ignition Coil - SOLD
Wiring harness and ecu SOLD
Radiator, shroud, elec fan, overflow tank $200
Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
I have a box full of misc bolts, nuts, etc.
I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
That would include....
Brake calipers, lines, pedal, master cyl, E brake assy,
Steering shaft, wheel
Ignition switch, key
Light bar frame, 2 lights
misc hardware, spindles
2 hubs, rotors
Engine mounts
Throttle pedal, cables
Shifter, cables
Clutch master, pedal
I am sure I am forgetting something.
I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
Thanks!
-
By brewski
I just purchased a 2025 kubota rtv 1100 x cab esd esnting to install light bars on the roof it appears to be prewired for lights how do lights mount and what kind of switches do i need
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.