Quantcast
Jump to content

Selling my 2007 Joyner 1100 Sand Viper


Recommended Posts

2007 Joyner 1100 Sand Viper $7000 or best offer

1100 cc Chery engine
4 cylinder
16 valve
dual overhead cams
Electronic Fuel Injection
86 hp
11 gal gas tank
over 40 mpg
4 speed w/reverse
disc brakes
5 point harness
turn signals
street legal

Additional added:

new 30" tires and 15" wheels
new swing arms, boxed
new rear bearings
radio
cb and antenna
spare tire rack
new rear springs
windshield with tinted glass
new throttle cable
new clutch cable
new open rear differential
new rear axles
new cv joints and boots

DSC06468.JPG

DSC06469.JPG

DSC06470.JPG

DSC06384.JPG

DSC06385.JPG

Bruce
714-743-3595
[email protected]
Located in Quartzsite, AZ

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By weasel
      starts up you have keep rpms up for 5 minutes till it warms up then runs fine. But if it stalls wont start unless you unplug fuel pump and hold it to the floor till it starts then plug pump back in and run it till it warms up then it is fine all day.
    • By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • By Round
      Bought a Massimo 500 last night. Stopped and filled it up on the way home and I put the wrong gas in it. Is there a drain plug on the bottom of the tank that I can get to or will I have to siphon it out?
    • By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • By FloridaMan
      I have a 2012 Massimo MSU 500 that died. I found that it didn't have spark and the fuel pump wouldn't run. Checked all fuses and none were blown.
      Went through and replaced the ignition coil, HT lead and spark plug. Still no spark.
      Thought it could be the fuse/relay box because I didnt' know much about the machine at that point so I replaced it. No spark.
      Then I replaced the ECM just because I was running out of ideas. No spark.
      I removed the 9 pin connector and hardwired it making sure that they were no wires got swapped. Still no spark.
      Then I replaced the wiring hardness. In doing so, I replaced the 9 pin connector with new ones. I made sure all wires were matched up between the engine harness side and the other harness assembly. Still no spark.
      I have no other ideas what to do. My fuel pump doesn't kick on and I have no spark. I have 12V on the fuel pump, ignition coil and fuel injector, but no ground from the ECM control.  I unplugged the fuel injector and waited for a diagnostic code but nothing ever came in. It makes me think that the ECM isn't powering up. I've checked for 12V on pins 18 (purple wire) and 15 (white and black wire). I also checked for ground on pin 2 (black wire). All are good.
      I am out of options here and I have no idea what else it could be. I have all connections redone and are coated with dielectric grease. I've checked all easy things like fuses and making sure I have 12V in the right placed. I would appreciate any help.
×
×
  • Create New...