Quantcast
Jump to content

C21tiger

New Member

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By 2scoops
      Anyone have an outer cv joint ball cage? Mine is cracked up. Other than that it's a good axel.
      Please let me know
    • By bnold
      Afternoon,
      Doing some much needed overdue maintenance on the Joyner T2.  Believe mine is a 2011.
       
      In need of :
      - wheel bearings and seals (small and large)
               Outer 65x45x8
               Inner 62x42x8
               Bearing 02.D650.03.01.0005 - 65x35x35
      - Inner tie rod joints
           D800.05.01.00.0002
      - Upper and lower ball joints
           S650.02.01.01.01.00
      and I'm sure I'll uncover a few others as I continue the tear down
       
      What's the most reliable for parts now?
       
      - Casey Ye from China, assuming shipping cost and time would be higher.
       - Klung, China contact as well I believe.
       - MPSRacing.net
       - Is ordering from Joyner-USA working for folks?
             Address: 1650 E Riverview Dr Ste 110, Phoenix, AZ 85034        Phone: (602) 253-0283 Don't want it torn apart in the shop for too long.
       
       
      Is there a parts manual floating around for ordering the correct parts?  I have a 2009 parts manual I believe, but there are definitely differences between that model and mine.
      Hate to order the wrong stuff.
       
      Thanks,
       
       
    • By mixfixdave
      I had been wanting to install power steering on my T4 for years so I went to the salvage yard last weekend and bought a complete column (minus airbag) out of a 2009 Nissan Versa for $125 with the ECU.
      It was a fairly simple install. The long shaft that fits to the Joyner steering rack actually fit perfectly into the Nissan column. Had to weld up a U joint on the Nissan column to make it a straight shaft and fab up one simple bracket. Connect power and ground plus a switched 12v and now I can steer with one hand!

       
    • By fettman1176
      Hello there, I have 4 T2 troopers, 2 of them start and run like Champs, 2 of them have the issue. They will crank and crank but not start. Takes about 20 to 30 minutes to get them going, then they will run all day long and fire up at will every time. It's just the cold start they have a problem with. Since I have 2 that run good, I have swapped every part you can think of from the fuel system to ignition system with no success. I'm pretty stumped and am looking for any advice 
    • By Volkz VLOGS
      Hi, I'm getting ready to supercharge my trooper and I'm looking for advice on the setup. So far I have... a AMR500 supercharger, small intercooler, Dolbeck EJK fuel controller and wideband. Looking for any advice on what else I'm going to need and what to expect..Thank you
       
       
       
  • Similar Tagged Content

    • By Volkz VLOGS
      Hi, I'm getting ready to supercharge my trooper and I'm looking for advice on the setup. So far I have... a AMR500 supercharger, small intercooler, Dolbeck EJK fuel controller and wideband. Looking for any advice on what else I'm going to need and what to expect..Thank you
       
       
       
    • By MauyThai1
      I have a 2009 Joyner T2 for sale.  1100 cc Turbo charged motor with five speed transmission. full cab with heater, up graded steering box, new himes joints, 2 inch lift with up graded shocks and travel limit straps, up graded induction system, remote oil filter station with two large filter which hold and extra gallon of oil, up graded rear diff, mud flares, up graded axels, up graded wheel bearings, extra set of 27 in tires, extra up graded diff as well as original shocks and axels. 12 inch wheel travel with 17 inches ground clearance. 6000 miles on unit. comes with 14 ft trailer with 3500 lb axel.   8500.00   This has been a great machine which I use for hunting only, never raced or hill climbed.  This machine has never been off it's wheels as in never been rolled or abused. You can contact me on this site or call 970-986-0268 as well as e-mail me at bugler [email protected]  I can send pictures if your interested.


×
×
  • Create New...