-
Similar Topics
-
By rdc
I have a 2007 Joyner 1100 sand viper and before it even get's to where the thermostat opens up the oil pressure get's so low I have to shut it down. What could fix this ? I thought about adding an oil cooler with fan, thicker oil, or removing the thermostat. Any advice?
-
By jertex
I bought a 2017 Stampede 900 last fall that was new, old stock with less than 5 hours on it thinking that I would be getting a relatively trouble free UTV as compared to buying a used Polaris or CanAm, or Honda, etc. It's been a little quirky, but reliable. What I thought was just a minor issue with this model, the difficulty in shifting between R, N, L, H, etc., was just a characteristic of this model is now a big problem. I had to climb two very steep trails to get to the upper meadow of our hunting property, which seemed to stress the UTV more than usual since I was carrying some lumber to work on a platform for a hunting blind, and when I went to shift into park, I felt something give and it would not shift out of low, but it did move up into high gear. I couldn't get it to shift at all at that point and the shifter felt mushy for lack of a better word. I was able to get it down to the lodge and when I investigated, I discovered that the straight, metal tube portion of the shift cable had bent to almost 90 degrees (see pics). I'm positive that it had already had some deformation that had happened previously and it had the right amount of resistance to bend to the point where it was unusable.
I have two questions:
1. I suspect that there must be some other issues that makes this UTV difficult to shift, and I'm wondering if this is a common problem and if someone could enlighten me on what could cause this to be difficult to shift?
2. Have any of you had this happen and if so, how difficult is it to replace the shifter cable?
Any other advice is welcome, this is the first UTV that I've ever owned, so I don't know much about working on these or maintaining them. I'm relatively capable when it comes to working on my own vehicles in general, and I'm not afraid to take things apart and get my hands dirty.
Thanks in advance for any insight, I'll be traveling most the day so I won't get a chance to look at replies until this evening.
-
By Butch
I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed.
-
By TimsBrickHouse
DO NOT BUY ANY THING FROM HISUN Period! I had the axis 700 for 2 months when a rat or squirrel ate both wiring harnesses. (Main & ECM)Wanna know why? Because the manufacture of these things in their infinite wisdom use either, a soybean oil or a peanut oil to run the wires through the the wire loom. Hmmm i wonder why they would be inclined to eat the wires. So now I have $10K machine that I've only had for 2 months when all this happened and they will not warranty it at all. It is going to cost me $800 to $1000 to get this fixed. Here is a link to a video showing where we took our Hisun notice how many are there:
https://photos.app.goo.gl/2FdniAoCyvTJMKae7
So counting mine, there are 16 of Hisun Axis on the lot that i took in for authorized dealer, with the exact same problem, plus other troubles that the mechanic explained to me. This particular place told me they are not going to work on them anymore. I will be posting this in as many places as possible to reach the masses. I hope its worth Hisun!
-
By JWS
Help Please!
Last year my Mule started running bad and was hard to start. NOT a battery or starter problem. I replace the carb with one of those cheap Chinese carbs from Amazon. Problem got worse. So, I replaced the fuel pump, one from Kawasaki, fuel filter and lines. Then replaced the fuel pump line to the engine. Finally bought a Kawasaki carb. Everything was ok till I filled the gas tank with fresh gas then it started running bad and hard to start again. The tank is clean. Gas is fresh, AGAIN. Filter is new. When running it has an occasional misfire. Managed to burn about a gallon out of the tank. Runs better. Replaced the gas cap in case it wasn't venting. No change. When running, if you try to go full throttle, it bogs down. The gas is good. I use it in my mower with no problem. The stater was replaced about one year ago and the flywheel cleaned inside. Still seams like a fuel problem but I'm at a loss. It's going back to the mechanic shop today. We use the Mule every day, live on a farm. It's never sat up. It has 1045hrs on it. New battery and starter.
Any ideas?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.