-
Popular Now
-
-
Similar Topics
-
By Sidewinder
All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.
-
By lmarkie
I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
Only problem is the exhaust exit is toward the back seat instead of out the back.
Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
Any thoughts?
-
By Benny Glasow
We have pretty much decided to buy a Polaris utv to use around the place and for some irrigation stuff. We were thinking about getting a windshield, top, and rear window. All the Polaris utv accessories are pretty pricey and I was wondering if anyone had used some after market accessories? Any other thoughts on stuff that we should put on it?
Thanks
-
By Jamesjoh
I just bought my first Polaris yesterday and I’m waiting for it to be delivered. I opted against getting the windshield and roof from the dealer — he roughly quoted about $1k for both, which seemed a bit steep — so I’m looking around online first.
I’m specifically shopping for Polaris Ranger XP 1000 accessories like windshield, roof, and other gear. Where do you all usually buy from, and do members here get any discounts or preferred vendors?
Thanks!
-
By Tommy2bits
Just bought a brand new 2022 (NOS) Sector E1 with Lithium upgrade. (Single 135ah/200amp continuous). I've climbed a moderate hill in my woods probably 20 times since buying it. Today It won't climb it unless I am in Low. In High it almost makes it and then completely dies and I have to roll back down the hill. In Mid range (Max Range) I can't get 2 feet up the hill and the power output in only 100 amps, I have climbed this hill in every speed before many times. I put it on the trailer tonight and it wouldn't even get on the dang trailer in mid range. Torque is gone. That being said, when I am just cruising around in Midrange, it runs absolutely perfect with plenty of power. The only thing I did was charge it up, that is all. I charged to 100% using the charger that came with the battery. Before you think the BMS is shutting down due to overcharge protection, remember I am going UP hill so there is no regeneration AND I have done it before at 100% charge AND another big problem is that after 1 mile it is already down to 85% so it's not over charging and why is the battery draining so fast when I got 27 miles before. Battery output is fine in Low it pulls 200 amp up the hill just like normal so that doesn't point to the battery being the issue. All the individual cells on the battery are in line, so there is no dead cell either. I am tech savvy but to toward electric motors and I tried to cover all my bases. Please don't tell me basics like torque is reduced in High and Mid. The only thing I can think of is that I smelled something when I took my first drive today and I thought it was the Ebrake dragging but there was the correct amount of play in the cable and I jacked up the rear wheels and they spin freely. maybe something burned out in the motor, I do not knowm still runs great, we'll see if I have any trouble on the hills at the lake house this weekend. Maybe this is "Normal" and the settings were off before and was giving equal torque for whatever reason instead of 50% in Mid and 70% in High like the manual says....
For reference....this is it not even able to get on the trailer in mid range
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.