Quantcast
Jump to content


Husqvarna 4421G

Dale Thompson

By Dale Thompson
in Other UTV SxS Forum

 Share
Go to solution Solved by Jim Kessell,

Recommended Posts

Dale Thompson Newbie

Dale Thompson

Posted
Posted

I'm working on my neighbor's Husqvarna 4421G side-by-side.  I think the year is 2007.  The rear wheels won't pull but they do spin when I have it up on jack stands.  With the transmission in neutral, I can turn either rear wheel by hand and neither the other wheel turns nor does the drive shaft turn.  Parts diagrams are sketchy and parts are largely unavailable, so I'm reluctant to tear into it without some idea of where the problem actually is.  Anybody have any experience with these?

  • Solution
Jim Kessell Apprentice

Jim Kessell

Posted
  • Solution
Posted

Make sure that the gear box has the correct fluid in it.  Mobil 424 which is a Hydraulic/Transmission type fluid. 

It won’t engage correctly if you use anything else. 
 

Jim

06 - 4420

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Sidewinder
      Polaris RZR 800 Rear Differential Pinion Nut Issue
      By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...