Quantcast
Jump to content


Recommended Posts

Posted

Bought my 2009 Yamaha Rhino, (fuel injected of course), recently from the original owner. Only had 500 miles and 70hrs. Starts reliably, however, it will not idle but about 50% of the time. Also, when driving slow in low or high, that is to say, relatively low rpms and below about 10 mph, it bucks and almost wants to die..... not smooth at all. However, at speed (say 12-15 mph or more) it runs very well, like it should. Any ideas?

  • Big Red Dog changed the title to 2009 Rhino 700 won't idle well
Posted

Bad fuel, clogged injector, air restriction? Check that fuel is flowing steadily from pump to injector by putting end of fuel hose into a container. Start with some basic tests.

 

Posted

You're right. Thanks for your reply. I should start with that. That will eliminate or confirm some things. Fuel is good. Ran 3 tanks through it with fuel injector cleaner. So I do not think clogged injector is the issue, especially since it runs fine above idle. It has no tach so I do not know exactly at what rpm it all smooths out, but at about 12+ mph it will run like a top. I found a You Tube video suggesting that it's an idle air control (IAC) unit issue. But with only 500 miles on it that should not happen. Now, those 500 miles was over 14 years, so the IAC could be gummed up.......So after checking fuel pump and double checking for air restriction, I guess I will find a pull the IAC and clean it.......

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
    • By Eman85
      I just purchased a Massimo MSU500 and no manual came with it so I have some questions. looking for part #'s and availability of basics like spark plug air and fuel filter. What is the valve adjustment specifications? 
        Is there a fuel drain? It's been sitting, low mileage but I want to drain out the old fuel and put fresh. 
    • By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
×
×
  • Create New...