Quantcast
Jump to content

UT400--120 days, 520 miles


cliffyk

Recommended Posts

As the title suggests, today marks 120 days and 520 miles since I bought my 2020 UT400 from Tractor Supply. I like it, here;s a synopsis of my experience so far:

Delivery on 10/29/2020 was uneventful, BUT my first ride was interrupted by the damned undocumented seat belt safety "feature", the staff at TS knew nothing about it, but somewhat accidentally I found the driver's belt was wired and "bugged"--problem #1 solved;;

Next I had to screw around with the State of Florida to get it registered and titled--that took a month and my trailering  it 150 miles round trip to have it "inspected' and documented as a 'low speed vehicle'"; 

Got it titled on 11/25/2020;

At 13-15 miles or so it decided it did not like shifting into reverse--the shift cable adjustment is finicky, with examination and trial and error I developed an adjustment procedure around the neutral position;

At 15 hours I changed the fluids as recommended;

Next, nothing major for the next 400 miles when I changed the front and rear gearbox juice just to make me happy;

Today I drove it to the beach (2.5 miles East, including 1.2 miles at 45+ mph (50 on the "Clock",  45 on the GPS)--the dog and I had a great time. This was the 4th or5th time I've had it "on the road" at 40+--it seems to like or at least tolerate it. Beach, dunes, deep sand no problems.

26 mpg overall  since new--not too bad.

It's a well engineered and built machine however Coleman and Hisun are shooting themselves in the foot with their crappy documentation--I've contacted both but they don't seem to care.

I like it!!!

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Travis
      View File Kawasaki Mule 550,520,500 Complete service manual
      This is a complete service manual for the Kawasaki Mule 500,520 and 550 models.
      Topics  covered include Brakes, Steering, Electrical system, suspension and fuel system. As well as engine repair procedures and Transmission/Final Drive procedures.
       
      ********************************************************************************************************************************************************************************************
      If you need more information about the engine this manual linked below is chock full of information.
      Thanks goes to @cliffyk for getting these files all  into one PDF format for uploading.
      Submitter Travis Submitted 04/18/2021 Category Kawasaki  
    • By AlaskaTrail
      Hi All,
      New to UTVs and recently accuired a ut400 from our local Alaska Commercial Co. and had a questions regarding the transmission fluid. I have had a squeeling noise, sounds like a teapot, that recently started after being driven for a few minutes. The manual says to change the fluid at 500 miles, so I was thinking maybe its just time for this to be changed. Other then that I cannot find any information regarding the type used. While reading through these forums, I seen someone put that the transmission is lubricated with the engine oil. Is this true? If not what should I be using and where can I find the information to change it out? Any input on this would be greatly appretiated!
      Thanks in advance
    • By aefron88
      I've seen a number of requests for the location of all the grease points on these machines, and there is no definitive list in the manual. This covers the UT400, but other Coleman/Hisun models should be similar.
      Tools:
      First to grease your machine you need a grease gun and some NLGI#2 grease. You will find it helpful to buy a needle attachment as pictured here, due to poor clearance on some of the U-joints. The rest of the zerks use the standard attachment.
       
      Technique:
      Wipe any dirt/grease off the zerk before greasing to prevent pushing gunk inside and causing excess wear.
      Push the grease gun on the zerk at a straight angle and give it a few pumps. You will hear an oozing noise or sea grease coming out from the outside of the greased area when you've put enough grease in, a few pumps should be plenty.
      If it's just oozing around the zerk you either don't have a good seat with the gun, or the zerk may be rusted and the check ball frozen. Try seating it again and regrease.
      Wipe up any excess grease when youre done to prevent making a mess.
      Greasepoints:



      Rear A-Arms are greasable with the wheels on from the rear, I took the picture with the wheel off for easier visibility

       
      That's it. All other Hisuns should be substantially similar.
    • By aefron88
      View File Hisun HS400/Coleman UT400 Parts Diagrams
      Compiled document with parts diagrams for Hisun HS400/Coleman UT400 for help in repairs where the service manual diagrams are poor or non existent.
      Submitter aefron88 Submitted 04/15/2024 Category Hisun  
    • By Jon C
      Hello to anyone who reads this. I am Jon and I own J&M Outdoor Power, a very small, small engine repair shop. I was approached by Coleman about 6 months ago to become one of their Warranty Centers.
      I recently received 3 different UT400's and a UT500 all with similar issues. These units range from 2 months to 2 years old. Customers state that the unit(s) was/were running fine, then heard a pop and a loss of power, two would no longer start. The two that would run would not achieve normal operating speed (around 20mph I would say) without redlining the RPMs. I quickly found that the Valve lash on each unit had become too large on some(both intake and exhaust) and too tight on one(just intake). 
      After setting the gaps to .005(I found multiple different people suggesting bigger and smaller gaps, but no definitive Coleman Spec number yet) every unit starts, runs, and achieves top speed without issue.
      I don't know how many others have come across these issues, and I wanted to get something out on the web for others in the same predicament. 
      Please let me know if you have had similar issues.
      Edit: I realize that this will not be a fix all solution for this issue, as the oil level and condition should be verified before moving to the valves. Many times improper oil conditions will cause valve lash to change. These units all have good oil and proper oil changes.
×
×
  • Create New...