Quantcast
Jump to content


BMS Ranch Stallion CVT Belt replacement

nitrohuffer

By nitrohuffer
in Other UTV SxS Forum

 Share

Recommended Posts

nitrohuffer Newbie

nitrohuffer

Posted
Posted

Hey Folks,

I have a BMS Ranch Stallion 4x4 that has been a really good UTV. I have recently burned the belt out by using it to get a tractor back on its feet after someone dumped it on its side. I found the belt online (380.00 bucks) and I have pulled the cover off to expose the belt. I pulled the old belt off but can not figure out how to reduce the tension on the pulleys. I do not know how to loosen the nut that hold the clutch on as it just spins the whole drive, how do i hold the spindle the nut threads onto? I can not find anyhing on the web about the bms ranch stallion and belt replacement. Anyone ever work on one of these?

  • Like 1
motojoe Contributor

motojoe

Posted
Posted

I would look at a Hisum or any other Chinese side by side that has the same engine size as yours their belt will probably fit, also look on e-bay as they sometimes give the belt sizes.  
As far as removing the belt just work it off by getting the belt off center and rotating the clutch.

 

  • 1 year later...
The_Chieftain_A Newbie

The_Chieftain_A

Posted
Posted

I have this same UTV and same problem(s). Cannot find any help on the www and I suspect the belt because of it's inability to move or very lethargic at best. The only difference for me is, I've yet to crack open the housing and actually inspect.

If the author reads this, may I please ask you for a small favor? Do you mind summarizing the steps you went through to perform this task? Any pictures would also be much appreciated. 

mine is either a 2020 or 2021 BMS Stallion 600 RX-EFI

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • Fmaxiron
      Honda Pioneer 1000-6 back windshield or screen.
      By Fmaxiron
      I just purchased a 2023 Honda Pioneer a couple of weeks ago and had the hard roof and a front Honda Pioneer windshield installed at the shop before taking ownership. As things are drying up here in NC, the grass and dust are beginning to fly right through the back of the cab while driving. I was wondering if anyone has any good recommendations on rear windshields, dust panels, or mesh screens to help stop this?
      Thanks a lot!
    • AaronD1982
      Massimo 400S Buck UTV Starter solenoid replacement
      By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?
    • RBonds007
      2019 Cub Cadet Challenger 400 online parts
      By RBonds007
      Looking for an online parts store.  Just need basic maintenance parts tune ups and such.  Any suggestions?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...