Quantcast
Jump to content

2014 massimo msu 500 rebuild/upgrade to 700

Working hard to hardly work
 Share

Recommended Posts

Working hard to hardly work Rookie

Working hard to hardly work

Posted
Posted (edited)

just picked up a massimo msu 500 for cheap, previous owner toasted the top end and it will definately need a rebuild, my curiosity is since alot of 700 parts crossover with the 500, would it work to drop a top end kit and head on a 500 lower? or would it have to be a complete engine swap? and would a 700 fit in a 500 easily?

Edited by Working hard to hardly work
new topic
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • great8redsfan
      2017 Challenger 500 No power on take off or hills
      By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • Buddee
      2010 500 - New Carb- Hesitation
      By Buddee
      Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?
       
      Any help appreciated!
       
       
    • htrotte
      2011 Massimo HS500UTV-EFI third temp switch?
      By htrotte
      #1   While troubleshooting an issue with temp warning light I discovered another temp switch mounted in the pipe going to the head  The two switches are literally 6 inches apart.  Does anyone know what this third switch is used for?  If i can figure out how I will post pictures.
      Author #2   Finally got the pictures took.  See the photo and tell me if you know what the switch on the right is.
      It looks to be factory and I know the girl who bought it new and she didn't install it.
      I can't find anything on it in any manual i have looked at.  Any help would be appreciated.

    • joel b
      Massimo Tboss 410 won't operate in reverse
      By joel b
      i purchased a brand new massimo tboss 410 and from day 1 it wont operate in reverse.  When i pop in reverse and give it gas it will die out.  when i pop in reverse sometimes in will die right away (before giving any gas) and 1 time out of 100 when i pop in reverse it will operate perfectly fine.   and yes, it operates perfectly dine in normal drive H and L.  any thoughts??   when i called the dealer i got it from they had no idea.  
    • BOYD
      Need to replace both front cv axels on my 2004 KUBOTA RTV 900 DIESEL
      By BOYD
      I have a 2004 KUBOTA RTV 900 DIESEL and I need to replace both front cv axels.I have been online looking at them and there seems to be a lot of different manufactures to choose from. My question is who makes a good aftermarket set of cv axels for this KUBOTA. I have read horror stories of people buying the  cheap Chinese brand only to find out they don't fit or they don't last very long and fail again. I hate to have to spend over $200 a shaft to get OEM from KUBOTA when I'm sure there is a company out there who probably makes it for them or makes comparable to OEM. Thanks for your help.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...