Quantcast
Jump to content


Recommended Posts

Posted

I have a 2009 Joyner Trooper 1100. I found that the Joyner Trooper ball joints were very poor quality, so I simply bought a similar size ball joint and the angle reamer, and they are much more robust. I find that with my trooper, a few things are just not made well and can use a few design changes. By in Large, the trooper is a very hardy machine and can be run trouble free if you don't treat it like a 1100 lb dune buggy and take it out jumping , etc.

  • 4 weeks later...
Posted

Rubber ball joints: These are the most common type of ball joint and are made of a rubber sleeve that is molded around a metal ball. Rubber ball joints are relatively inexpensive and easy to replace.

Polyurethane ball joints: These ball joints are made of a polyurethane sleeve that is molded around a metal ball. Polyurethane ball joints are more durable than rubber ball joints and can withstand more wear and tear.

  • 1 year later...
Posted

My dad and I purchased a Joyner 1100 T2 that we are currently going through. we found that the MOOSE 0430-0664 ball joints are perfect to be pressed in. The only thing that we had to do was using an 18mm drill bit we bored out the hub @ the lower and upper ball joint holes. the bolt still works with the bigger hole and everything mounted up nice. here are the ones we bought also for a cheaper solution through amazon. they may not be name brand but they are definitely a lot better than the ones that were on the vehicle now thats for sure.

 

https://www.amazon.com/706202045-Maverick-Defender-Outlaner-Renegade/dp/B082VKF359/ref=sxin_17_pa_sp_search_thematic_sspa?content-id=amzn1.sym.2da95b6c-f59a-4699-bc43-d0ff036c6388%3Aamzn1.sym.2da95b6c-f59a-4699-bc43-d0ff036c6388&crid=ISDAA9CBEKDV&cv_ct_cx=can+am+maverick+x3+lower+ball+joints&keywords=can+am+maverick+x3+lower+ball+joints&pd_rd_i=B082VKF359&pd_rd_r=1620e65a-622e-497d-bbe3-afa868754518&pd_rd_w=dWyw9&pd_rd_wg=pCEhp&pf_rd_p=2da95b6c-f59a-4699-bc43-d0ff036c6388&pf_rd_r=04DEW3MWYRJNMDEHBV22&qid=1749575580&sbo=RZvfv%2F%2FHxDF%2BO5021pAnSA%3D%3D&sprefix=can+am+maverick+x3+lower+ball+joints%2Caps%2C166&sr=1-1-6024b2a3-78e4-4fed-8fed-e1613be3bcce-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9zZWFyY2hfdGhlbWF0aWM&psc=1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Robert Hamilton
      i am looking for front brake calipers and brakes for my 2008 ruesch xr side by side
      Can anybody help me
      Thanks bob
    • By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • By RBonds007
      Looking for an online parts store.  Just need basic maintenance parts tune ups and such.  Any suggestions?
    • By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
×
×
  • Create New...