Quantcast
Jump to content


adjusting linkage? clunk/grind when going into gear 4010 Mule

C H

By C H
in Kawasaki UTV SxS Forum

 Share
Go to solution Solved by C H,

Recommended Posts

C H Newbie

C H

Posted
Posted

I have a 2023 4010 Mule TRANS that I've now had a year and just hit 50hrs.  I did my first service including oil change, trans & differential oil change.  I'd like to adjust my linkage (I suppose) as when I shift into gear, I get a good grab and clunk at least. It was grinding at one point and I tinkered with the linkage adjustments enough that its finally not grinding. Still, sometimes I worry that it's clunking too hard when I go into gear. 

 

Looked on youtube and can't find any vids or advice there on the adjustment procedure. I'm STILL trying to find somewhere that has the service manual available. Even the company site is telling me that they hope to have them in stock by Christmas! 

 

These are the two places I was trying to adjust. Are these even the correct ones? Does anyone know the difference in the two?

?hash=af89f8b41b515af765af7f6c26cc2293

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • carbdoctor
      2023 massimo 850 eps overheating
      By carbdoctor
      I have an 850. It’s been overheating. The electric fan is not kicking on. I see the temperature switch going into the radiator, but there’s no wire plugging in to it or none to be found in the area. i’m thinking I might’ve hooked on a branch and it ripped out the harness on that part. Does anybody have a picture or no where that plugs into on the harness? On the top of the firewall, I did notice some plugs that have nothing plugged into it. I was wondering if it’s a harness that goes from there down to the radiator that was pulled off


    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Sidewinder
      Polaris RZR 800 Rear Differential Pinion Nut Issue
      By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • mike.s.
      Kawasaki mule model 2010, 4x4, gas motor, sell or trade
      By mike.s.
      SOLD 
       
       
       
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...