Quantcast
Jump to content


Tboss 410 Problem with gears grinding when trying to put in forward or reverse.

Dreaded

By Dreaded
in Massimo UTV SxS Forum

 Share
Go to solution Solved by Dreaded,

Recommended Posts

Dreaded Rookie

Dreaded

Posted
Posted

This tboss 410 started having a problem with I think clutch not releasing. If you have it in forward with neutral safety disabled and try to turn it over, it will try to move forward. Neutral does work correctly.
What I was told occurred was he was trying to back up a hill and was trying to pull a load. He said that it all of sudden died and would not go into gear. To get it back he disabled the neutral safety and started engine and drove back but had to switch to neutral to stop.
Is this going to be the centrifugal clutch on the drive belt or could it be something else?

  • Solution
Dreaded Rookie

Dreaded

Posted
  • Author
  • Solution
Posted

 I decided to tear it down since it took a couple days to get site approved. What I found is the clutch melted and froze.
Pics show it all. I took the clutch apart and found clutches jammed up and not movable.
I ordered a new secondary clutch to replace it, the primary drive seems ok so I will reused it.
 

IMG_20230809_144849424.jpg

IMG_20230809_151139976.jpg

IMG_20230809_151210871.jpg

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • TapBoss
      TBoss Enclosure
      By TapBoss
      So I’d been shopping for an enclosure for my ‘21 TBoss pretty much since I bought it. Then they came out with half doors and that’s the only one that I could find. Then the other day I ran across one on Amazon for half the price of anything else I’d seen. The link is below and I’m pretty impressed by how well it fits. There is one Velcro strap on the top of the door that doesn’t line up well with the roll cage, but I’ll work around it. 
      https://a.co/d/09ACQ191
       
    • rdc
      Joyner 1100 oil pressure problem.
      By rdc
      I have a 2007 Joyner 1100 sand viper and  before it even get's to where the thermostat opens up the oil pressure get's so low I have to shut it down. What could fix this ? I thought about adding an oil cooler with fan, thicker oil, or removing the thermostat. Any advice?
    • jertex
      Shift cable problem, 2017 Stampede 900, need advice
      By jertex
      I bought a 2017 Stampede 900 last fall that was new, old stock with less than 5 hours on it thinking that I would be getting a relatively trouble free UTV as compared to buying a used Polaris or CanAm, or Honda, etc. It's been a little quirky, but reliable. What I thought was just a minor issue with this model, the difficulty in shifting between R, N, L, H, etc., was just a characteristic of this model is now a big problem. I had to climb two very steep trails to get to the upper meadow of our hunting property, which seemed to stress the UTV more than usual since I was carrying some lumber to work on a platform for a hunting blind, and when I went to shift into park, I felt something give and it would not shift out of low, but it did move up into high gear.  I couldn't get it to shift at all at that point and the shifter felt mushy for lack of a better word. I was able to get it down to the lodge and when I investigated, I discovered that the straight, metal tube portion of the shift cable had bent to almost 90 degrees (see pics). I'm positive that it had already had some deformation that had happened previously and it had the right amount of resistance to bend to the point where it was unusable. 
      I have two questions:
      1. I suspect that there must be some other issues that makes this UTV difficult to shift, and I'm wondering if this is a common problem and if someone could enlighten me on what could cause this to be difficult to shift?
      2. Have any of you had this happen and if so, how difficult is it to replace the shifter cable?
      Any other advice is welcome, this is the first UTV that I've ever owned, so I don't know much about working on these or maintaining them. I'm relatively capable when it comes to working on my own vehicles in general, and I'm not afraid to take things apart and get my hands dirty.
      Thanks in advance for any insight, I'll be traveling most the day so I won't get a chance to look at replies until this evening.


       
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • esmarkey
      2018 cub cadet 750 challenger clutch issues?
      By esmarkey
      Hi, I purchased a used Cub Cadet 750 Challenger that seemed like the belt was slipping so I put a new belt in.  It still acts like the belt is slipping but now I am thinking it is the clutch? 
      What is the best way to remedy this problem? 
      Can the clutch be rebuilt?
      Are there aftermarket clutches available? 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...