-
Similar Topics
-
By Phil S
I have a Massimo Buck 450 and last winter I had the snow plough added by my dealer. After about 15 minutes of ploughing the plough went down but would not lift up. Upon inspection, it appears that the winch is permanently in the free-spool. When you try to wind back in the spool just spins. It is out of warranty and upon looking at replacing I am not sure how I would go about it.
Has anyone had similar issues?
Has anyone replaced it with a new winch? is so what model and how was it installed?
Any help is welcomed.
-
By Wolfpaak
Pink Floyd quote/reference.
i am looking for a starter for my 2004 800 Renegade and apparently the place I dealt with before is no longer in business. Any help?
Thanks in advance,
Kenny
-
By Greg Kilgore
We all know summer is hot inside the cabs of our SXS. So I've rigged up a couple of fans to help cool down the cab.
I didn't want to drill the fan's "support rails" into the ROPS (Roll Over Protection System), aka roll bars. So I used water clamps to hold them in place.
I just need to replace the wires I ran with bigger gauge. Then finish the wiring to switches, relays, and battery. But the hardest part. The actual mounting of the fans is complete. Also just in case anyone plans on doing this. I may have to only use 1 fan in the middle instead on 2. Due the the draw on the battery.
The fans are 12", 12V 80W. So I'm figured they were 6.7 amps apiece. Used the WAVe formula to get unknown values Watts=Amps*Volts then solve for unknown. I know the watts and volts from sticker on fan. So just used above formula to get amps. So a 7 amp fuse should be OK and a 10 amp fuse will be good.
So pulling 14 amps from the battery all day may be too much for the charging system to keep up with. And I haven't even installed the radio yet. So I will have to test and let you know.
See pics below.
-
By papillion22
I'll start by saying i'm learning as i go & have come a long way, but there are some maintenance issues on my mule sx that must be addressed & i've got nobody around with experience & cannot bring it to a shop.
I've got rolling resistance when i jack up the front wheels. Months ago i thought i was possibly a brake issue but didn't yet have the equip. to pull the wheel hubs or press them back on... but the noise/friction seemed to resolve itself. I just checked up on it because i've got the tools for dealing with the brake system now and i noticed the wheels dont really spin... theres a lot of resistance and i can hear it coming from the front diff. I can't remember if it used to do that before, but i dont think it did. Its not the drive shaft or u-joints, but i've yet to pull them to be certain. it really sounds like its in the front diff. just where the drive shaft connects.
Should the front wheels - when in neutral and in 2wd and no diff. lock - spin freely? Theres too much drag for mine to even go once around. Can anyone point me in a direction? Otherwise its trial and error with cv axles, ball joints, brakes, etc. and i dont have the $ or time for that.
I'm in over my head and really hoping someone can help. I'll try to make a video of whats happening, hopefully the sound will come through well. Maybe that will help diagnose it. Thanks.
-
By Andrew Jake Bryant
Thanks for stopping by. I live out in the country and wanted to get a good Side By Side to get around my land and the local township I live in. I picked up a '23 bobcat UV34XL (Gas), and I hope I don't bug anyone with all the Questions that I will/may have.. I look forward to reading and having conversations with everyone.
-
-
-
Gallery Images
.jpg.84decc2b5f73a0d00e4b249aedfba113.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.