By Nickie Watts
I have a Hisun Strike 1000 I have been trying to get going, it has only 39 hours on it, so I can only assume it has been sitting for a long time.
The issue is it is losing spark to both coils after 20-30 seconds of running, doesn't matter if it's WOT or Idle, it will shut down. What sends signal to the coils to fire? It has a crank sensor, I was thinking a CDI box, but I have not found one of those on the machine.
The rear end was busted on it when I got it, So I ordered a new one and installed it only to run into this problem. I can only imagine the problem has happened over it sitting so long and not being driven.
I originally thought it was a fuel problem, so I checked the injectors, throttle body, o2 sensors. Discovered the heating element in one of the o2 sensors was bad, so ordered both and also replaced both injectors just to be sure, then discovered it is only losing spark.
I live on 11 acres that demands a bit of maintenance, and co-own a large farm a couple of hours away that I hunt on (professionals do the farming). My mowing/brush control/trail maintenance duties are handled by a 57" rough cut mower (Kunz brand), and I also drag logs and pull sprayers and seeders for food plots and such.
I've been using a pair of ATV's for decades to handle this work - a 750 for when I need real power (or need both machines at the same time when I have help) and a 500 cc with fixed rear axle for most duties.
Some of the places I need to work are VERY rough, and very three-dimensional, with steep ups and downs and some side-hilling I've learned the hard way not to try with my independent rear suspension 750, but handle with ease with my fixed rear suspension 500.
I've decided I want to sell the 750 and replace it with a UTV that I hope to use as my main workhorse. If anyone makes a working UTV that fits my specs that's what I'm gonna do. This is an all-work machine, I don't do any recreational riding so don't care about things like top speed.
So looking for advice on what models might handle what I'm looking for:
2 passenger (1 row)
Selectable gearing (not CVT)
Power-assisted dump bed
Engine cooling adequate for all-day slow-speed work in the summertime. Like towing a 700lb mower at 4mph all day in 100° weather)
Beefy tow rating, including tonque weight. Nobody ever mentions tongue weight because that exposes how crappy independent rear suspension is for towing safely in rough terrain.
Selectable locking diff
Fixed rear axle (Isolates tongue weight from rear suspension. Holds more stable & consistent center of gravity than IRS over side-slopes and other complex terrain, and keeps geometry and suspension response consistent over wide range of tongue-weight of towed loads)
Slow speed cruise control (Factory option or aftermarket, covering at least 4mph - 10mph. For calibrated spraying and controlled mowing speed.
Muffler designed for quiet operation for comfortable all-day use, and to minimize disturbance for getting to hunting grounds. Not concerned about normal motor noise, but don't want something specifically piped to "sound fun".
Any advice on brands or models I'm most likely to have luck with?
By Greg Kilgore
We all know summer is hot inside the cabs of our SXS. So I've rigged up a couple of fans to help cool down the cab.
I didn't want to drill the fan's "support rails" into the ROPS (Roll Over Protection System), aka roll bars. So I used water clamps to hold them in place.
I just need to replace the wires I ran with bigger gauge. Then finish the wiring to switches, relays, and battery. But the hardest part. The actual mounting of the fans is complete. Also just in case anyone plans on doing this. I may have to only use 1 fan in the middle instead on 2. Due the the draw on the battery.
The fans are 12", 12V 80W. So I'm figured they were 6.7 amps apiece. Used the WAVe formula to get unknown values Watts=Amps*Volts then solve for unknown. I know the watts and volts from sticker on fan. So just used above formula to get amps. So a 7 amp fuse should be OK and a 10 amp fuse will be good.
So pulling 14 amps from the battery all day may be too much for the charging system to keep up with. And I haven't even installed the radio yet. So I will have to test and let you know.
See pics below.
By Spencer Marks
I just finished replacing my front and rear drive shafts. I drained and put new dif fluid in the rear dif. I went to the local dealer and they told me the fill capacity of the front and the transmission as I want to replcae that as well but they could not tell me how to access the fill. One how do I access the fill for front dif and 2 is the transmission fill the same as the rear dif? I don't see a dip stick or fill for the transmission but all in same area.
Also, anyone can suggest a good shop/service manual for this bike?