Quantcast
Jump to content


Hello, I’m Rufus from the Bayou state!

Rufus Fruge

By Rufus Fruge
in New Members Area

 Share

Recommended Posts

Rufus Fruge Rookie

Rufus Fruge

Posted
Posted

Just wanted to check in and say hi to fellow members. I bought a 2023 T-Boss 550 last month just in time for hunting season. So far all is well. I went over it to check things out and learned a lot in the process.LOL! I certainly would recommend that all new purchasers should make it a point to do this because I can promise you that you won’t regret it.

  • 3 months later...
buckrub Rookie

buckrub

Posted
Posted

Hello Rufus! Here's another bayou boy. Just signed on and looking forward to talking with you fellows. We just boiled 120 lbs. of crawfish the other night. Sooooooooo good. LOL

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • carbdoctor
      2023 massimo 850 eps overheating
      By carbdoctor
      I have an 850. It’s been overheating. The electric fan is not kicking on. I see the temperature switch going into the radiator, but there’s no wire plugging in to it or none to be found in the area. i’m thinking I might’ve hooked on a branch and it ripped out the harness on that part. Does anybody have a picture or no where that plugs into on the harness? On the top of the firewall, I did notice some plugs that have nothing plugged into it. I was wondering if it’s a harness that goes from there down to the radiator that was pulled off


    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Jamie 67
      Why is there 2 different length keys for my tboss 1000
      By Jamie 67
      Why is there 2 different length keys for my tboss 1000?
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • marvin schuchart
      Kioti 2023 K9 2400 cab.
      By marvin schuchart
      Has anyone with a K9 2400 had issues your machine, My wife uses this one around the house. We have 60 pampered miles on hers and had a few issues. The master cylinder went out the 1st 30 miles, and again the master cylinder went out at 60 miles, I have been waiting for the dealer to install a new one for over a month now. the electric dump unit went bad at 55 miles, used it 5 times, window winder knob broke off handle on both sides, after a rain when I pull out it's a wall of rusty water that runs down firewall inside cab. Rusty water runs out tail gate when I lay it down, had to drill holes in bottom of tailgate to let rainwater out. I have a Polaris Ranger and a Kubota side by side, both have over 1600 hours and only had to do routine maintenance on these 2 old machines

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...