Quantcast
Jump to content


UTV Oil Change

Wesley

By Wesley
in UTV General Discussion

 Share
Go to solution Solved by Joe Breaux,

Recommended Posts

Wesley Newbie

Wesley

Posted
Posted

I have a 2022 500 Hisun product, I have had them in the past. I change my oil myself and trying to drain through the hole where I remove the plug is a mess.  How does everyone keep the belly pan clean during the oil and filter service?

 

Wes Jackson

  • Like 1
T-boss 410 Experienced

T-boss 410

Posted
Posted

I may have gone too far when I did my last oil change, but I removed the belly pan. It made things much easier, as I could see what I was doing much better. I believe there's only a few machine screws holding it on.

BlueFlag Rookie

BlueFlag

Posted
Posted

I agree completely with removing the belly pan as part of the oil change.

Only 6 screws hold it on, and they are easily removed with a drill driver and socket.

I just got done doing the oil change on my 2022 Massimo 550F (Linhai 493, w/oversize dropside steel bed),

All of the grief I endured with oil splurt, oil filter drainage and dropped parts & tools made me regret not removing that pan.

Besides, at this point you also have the opportunity to clean the dirt, mud and stones that have accumulated in the area under the engine.

RR

  • 6 months later...
Wesley Newbie

Wesley

Posted
  • Author
Posted

So folks, I changed the oil on my 2022 AXIS 500 this Spring but forgot to take this conversation one step further. The belly pan on my machine is metal and welded to the frame. Taking it off is not an option but on this model the oil drain hole is large enough to allow changing the oil a breeze. Yes if oil got on this belly pan some brake clean and a rag would take care of the problem. This is my last comments on the matter.  

  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Hunterman22
      2021 Hisun 500 Axis. Reading Codes??
      By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...